Filter
Top Products
Operation Instruction
50
NOTE: The location of camera screen can be changed by using the mouse. When in one of the multiview formats,
click the left mouse button on the camera screen and dragging it to where you want it located, and the
location of two camera screens will be switched each other.
In the 1P5 or 1P7 display mode, the main channel indicates the channel displayed on the large screen
which is displayed in the top-left. You can select the camera you want to display on the main channel
screen. Select a channel on the screen and click the right mouse button to display the Camera Menu.
Selecting Go To Main swaps the selected channel with the main channel. This function is supported
only in the 1P5 and 1P7 display modes and can be activated from any of channel screens except the main
channel screen.
You can change the location of the PIP (Picture-in-Picture) counterclockwise or clockwise
by pressing the Up and Down arrow buttons and change its size by pressing the Left
and Right arrow buttons. To change its location and size by using the mouse, select
the PIP and then click the right mouse button to display the following menu. Select the
options you want. You can also change the location of the PIP by clicking the left mouse
button on the PIP window and dragging it to where you want it located, and change the
size of the PIP by clicking the left mouse button at the corner of the PIP window and
dragging it until it is the desired size.
Previous Group, Next Group: Selecting Previous Group or Next Group moves to the previous or next page.
Edit Group: Selecting Edit Group enters the cameo mode. Refer to the following Active Cameo Mode section for details.
OSD: Selecting OSD toggles OSD On and Off.
Freeze
Selecting
(Freeze) in the Live Monitoring menu will freeze the current image on the screen until you select again.
It is the same as pressing the
(Play/Pause) button. Pressing any button except for the MENU button while in the
Freeze mode can also exit the Freeze mode. While in the Freeze mode, the icon displays in bottom-left corner if
Freeze is selected in the Display setup screen (OSD tab).
Sequence
Selecting
(Sequence) in the Live Monitoring menu causes the cameras to display sequentially. When in one of the
multi-view formats, pressing this button will cause the DVR to go through predefined screen layouts (Full Sequence).
Or, the bottom, right screen will display live cameras sequentially (Cameo Sequence). For example, if you select
(Sequence) in the Live Monitoring menu in the 2x2 format, the DVR changes pages as follows:
< Full Sequence >
< Cameo Sequence >
Selecting again in the Live Monitoring menu exits the Sequence mode. While in the Sequence mode, the icon
displays in bottom-left corner if Sequence is selected in the Display setup screen (OSD tab). If all the cameras in a page
are Off, or have lost video or are set to Covert (unless the user has authority to view covert cameras), that page will be
excluded from the sequence.
NOTE: The Full Sequence for the full sequence monitoring and the Cameo Sequence for the cameo sequence
monitoring should be selected in the Display setup screen (Main Monitor tab).
Camera Menu
Selecting
(Camera Menu) in the Live Monitoring menu displays the following Camera Menu.
Camera: Selecting Camera and choosing the camera number displays the selected camera full
screen. It is the same as pressing the individual camera buttons on the front panel or clicking the
left mouse button on a camera image when in one of the multiview formats (i.e., 2x2, 1P5, 1P7, 3x3
or 4x4). Clicking the left mouse button on the screen again returns to the previous display mode.
Screen: Selecting Screen and choosing the screen mode (PIP, 2x2, 1P5, 1P7, 3x3 or 4x4) displays
the cameras in the selected multiview screen mode. Selecting each display mode is the same as
scrolling the mouse wheel up and down when in one of the multiview formats (i.e., 2x2, 1P5, 1P7,
3x3 or 4x4).