Filter
Top Products
44
EN
3 Recording Date:
When press [Cursor D] at the current date, the
setting will change as follows.
e.g., 1st January
Skip:
Select this item only when you want to deactivate
the periodical (Daily, Mon-Fri or Weekly) Timer
Recording temporarily. To do so, move the cursor
to the Skip section and then press
[Cursor
U / D].
Check mark will appear and press [ENTER] to
activate the setting.
4 Start Time:
5 End Time:
6 Rec Mode:
Refer to “Rec Mode” on page 35.
7 Recording Media (HDD or DVD):
To record onto the HDD, select “HDD”. To record
onto a disc, select “DVD”. VCR is not compatible
with Timer Recording.
8 VPS/PDC system:
Refer to “VPS (Video Programme System) / PDC
(Programme Delivery Control)” on page 45.
• VPS/PDC system is only available for HDD.
• VPS/PDC system is not available for periodical
timer programme.
3 Select an item to set using
[Cursor
L / P], and set the contents
to suit your preference using
[Cursor
U / D].
4 Press [ENTER] when all the
information is entered.
The icon will appear on the Front Panel
Display indicating one or more Timer Recordings
are in standby.
•Press [CLEAR] will reset all the entered
information.
• To set another programme, repeat steps 2 to 4.
• When programmes are overlapped, a warning
message “All or part of the programme will not
be recorded.” will appear.
- When icon appears, a part of the programme
will not be recorded.
- When icon appears, the whole programme
will be recorded.
For details on overlapped Timer Programmings,
refer to “Hints for Timer Recording” on page 45.
5 Press [TIMER PROG.] to exit.
• You can also press [SETUP] twice to exit.
• If you press [ ON / STANDBY] to turn the
unit to standby mode, it will turn on 2 minutes
before the programmed recording time, and
start recording at the programmed recording
time. When the recording is completed, the unit
will ask you whether to turn off the unit.
The unit will be turned off automatically if you
select “Yes” or if you do not reply in 1 minute.
• To stop recording in progress, press [STOP S].
Confirmation message will appear. Select “Yes”
using [Cursor
L / P].
Relay Recording:
When you Timer Record to DVD, the unit
automatically changes the recording media to
HDD under the conditions listed below:
- when there is no recordable disc in the unit.
- when the disc does not have enough space for
the recording.
- if the unit is formatting or finalising a disc.
This feature is available only for Timer Recording
but not for OTR.
Note
• If you have not set the clock, the clock setting
window will appear instead of Timer Programme List
at step 1. Continue from step 3 in “Setting the Clock”
on page 30 before programming the timer.
• If a basic recording or One-touch Timer Recording is
in progress on the VCR and the Timer Recording set
for HDD or DVD is about to begin, the unit will
automatically switch to the programmed channel
within 15 seconds before the programmed time, and
the recording in progress on the VCR will be
cancelled UNLESS their recording channel is the
same. If their recording channel is the same, the
Timer Recording for HDD or DVD will start without
cancelling the recording currently in progress on the
VCR. In this case, the recording of the same
channel will be made on both VCR and the HDD or
DVD.
• The maximum recordable duration is 7 hours for
Video mode discs, 8.5 hours for VR mode discs and
5 hours for +VR mode discs.
• If the recording time exceeds 12 hours, a Timer
Recording cannot be set.
• If the starting time you entered is already in the past,
the recording will start as soon as you activate the
Timer Recording by pressing [ENTER] at step 4.
• If playback and recording are in progress at the
same time, select the appropriate device by
pressing [HDD], [DVD] or [VCR] before you press
[PAUSE p] or [STOP S] to pause or stop the
operation.
• When the Timer Recording is finished, confirmation
message will appear. If there is no signal for about
1 minute, unit will turn off automatically.
• If DVD+RW / R were used for the Timer
Programming with SLP mode, the Rec Mode will
change to EP mode.
• When VPS / PDC is set to “On” for timer recording,
you may hear some noise from the unit while the unit
is in timer standby mode. This is not a malfunction.
Daily
M-F
01/01
31/01
W-Sat
W-Fri
W-Sun
Weekly recording
E3B90ED_EN.book Page 44 Friday, February 23, 2007 12:38 PM