Filter
Top Products
26
EN
Manual Tuning (ANALOG)
You can preset an analogue channel manually and
individually.
1 In stop mode, press [SETUP]. Select
“General Setting” using [U \ D],
then press [ENTER].
2 Select “Channel” using [U \ D],
then press [ENTER].
3 Select “ANALOG Channel Setup”
using [U \ D], then press [ENTER].
4 Select “Manual Tuning” using
[U \ D], then press [ENTER].
5 Select “Position” using [U \ D], then
press [P].
6 Select the position number you want
to use using [the Number buttons] or
[U \ D], then press [L].
• You can select position number 901-999.
•With [the Number buttons], you only need to
enter the last 2-digit numbers.
7 Select “System” using [U \ D], then
press [P].
8 Select “L” or “BG” using [U \ D],
then press [L].
• If your system is SECAM-L, select “L”.
• If your system is PAL-B/G, select “BG”.
9 Select “Channel” using [U \ D],
then press [P].
10 Press [U \ D] to start scanning.
• The tuner will begin to search up or down
automatically. When a channel is found, the unit
will stop searching and the picture will appear
on the TV screen.
• You can select a desired channel number using
[the Number buttons]. Refer to the following
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then
press [0] and [4]. Or press [4] and then “– – 4”
appears and wait for 2 seconds.)
• If this is the channel you want, press [L].
[L (SECAM-L)]
[BG (PAL-B/G)]
This unit can receive the Hyper and Oscar
frequency bands.
• If “Skip” is set to “ON”, select “Skip” using
[U \ D], then press [P]. Select “OFF” using
[U \ D], then press [L].
• If you want to decode scrambled signals, select
“Decoder” using [U \ D], then press [P]. Select
“ON” using [U \ D], then press [L].
• To store another channel, repeat steps
5 to 10.
11 Press [SETUP] to exit.
Skip a Preset Channel
You can set the unit to skip channels. You can no
longer receive or watch when you access channels
using [PROG. G\H].
1 Follow steps 1 to 4 in “Manual Tuning
(ANALOG)” on this page.
2 Select “Position” using [U \ D], then
press [P].
3 Select the position number you want
to skip using [the Number buttons]
or [U \ D], then press [L].
4 Select “Skip” using [U \ D], then
press [P].
5 Select “ON” using [U \ D], then
press [L].
• To skip another channel, repeat steps 2 to 5.
6 Press [SETUP] to exit.
ANALOG
901
Manual Tuning
Position
Channel
Decoder
Skip
1
OFF
ON
System L
Channel Plan
CH Indication TV Channel
01 – 10 F1 - F10
21 – 69 E21 – E69
74 – 86 B – Q
90 – 106 S4 – S20
121 – 141 S21 – S41
Channel Plan
CH Indication TV Channel
02 – 12 E2 - E12
13 – 20 A – H (only ITALY)
21 – 69 E21 – E69
74 – 78 X, Y, Z, Z+1, Z+2
80 – 99, 100 S1 – S20, GAP
121 – 141 S21 – S41
ANALOG
E3NG0FD_EN.book Page 26 Wednesday, January 30, 2008 10:37 AM