Filter
Top Products
13
RQT9431
Auto Set Up (freesat)
Search and store TV programmes automatically.
These steps are not necessary if the setup has been completed by your local
dealer or freesat registered dealer.
Preparation:
Turn on the television (and connected equipment)
and select the video input terminal that this unit is
connected to.
•
TV’s remote control
to turn the unit on.
Auto Setup will start to search for TV
programmes and store them in the
numbered order as specified by the
broadcasters.
Check signal quality/strength
displayed on the screen (➔ right). If
the signal is weak, Auto Setup will
not start. Check that the satellite
dish is correctly positioned and
connected.
Enter your Postcode.
Press [
e
,
r
,
w
,
q
] to
select the character, then
press
[OK].
Repeat step .
Press the “Green” button to confirm.
Your postcode is required to receive local services and sort the channel order.
Press the numbered buttons to enter your choice
of a 4-digit PIN.
This PIN will be used only for the Owner ID-Data Entry screen.
0
9
8
7
6
54
3
2
1
abc def
jklghi
mno
tuvqrs
p
xyz
w
–
–
–
Owner ID
Please enter new PIN
PIN * * *
0
-
PIN entry
9
RETURN
*
You now have the opportunity to enter your
details and help the police to crack crime.
See Instruction Book.
Owner ID
Please enter new PIN again to confirm
PIN * * *
0
-
PIN entry
9
RETURN
*
You now have the opportunity to enter your
details and help the police to crack crime.
See Instruction Book.
freesat Auto Setup
DISH Input 1 Signal Quality 0 10
DISH Input 1 Signal Strength 0 10
DISH Input 2 Signal Quality 0 10
DISH Input 2 Signal Strength 0 10
TV Channels Found 0
Radio Channels Found 0
Data Channels Found 0
Searching
Channels found, creating channel l st
Exit feesat setup
Enter Postcode for local channels including space
Postcode
ABCDEFGHIJKLMN
UVWXYZ 0123456
OPQRST
789
RETURN
Set character
Select
Select
Delete Confirm Delete a l
The bar appears beside
Signal Quality and Signal
Strength when the signal
is input.
PAUSE
STOP
SLOW/SEARCH
PAGE
CH
AV
TV
DRIVE
SELECT
VOL
SKIP
PLAY/x13
SELECT
INPUT
DEL
0
9
8
7
6
54
3
2
1
abc def
jklghi
mno
tuvqrs
p
xyz
w
TIME SLIP
STATUS
REC MODE
REC EXT
LINK
CREATE
CHAPTER
G
U
I
D
E
RETURN
BACK/
DIRECT
TV
REC
EXIT
OK
OPTION
D
I
R
E
C
T
N
A
V
I
G
A
T
O
R
F
U
N
C
T
I
O
N
M
E
N
U
CH
MANUAL SKIP
Tips
To cancel the Auto Setup
Press [BACK/RETURN ].
To restart the Auto Setup (➔ 96, freesat
Auto Setup)
To correct the character
Press the “Red” button to delete character
one by one.
You can delete all input characters by
pressing the “Blue” button.
You can perform this operation in step
,
or .
Notes
To initialise all settings (➔ 104, Shipping
Condition)
When the below screen appears after
step
.
RETURN
St charate
elet
Se ect
freesat Auto Setup
No satellite signals detected at dish 2 input
Please check d sh installat on / connection before start ng search
otherwise record / playback functions will be lim ted
This screen appears when this unit does not
detect the connection to DISH IN 2.
When you connect DISH IN 1 only press
[OK], then go to step .
When you connect both
DISH IN
1 and 2,
turn this unit off and check your
connection. Then perform from step .
The Auto Setup may require a certain
length of time.
•
•
•
Quick Start Guide
STEP 3
(continued on the next page)