Filter
Top Products
3 - 11
4 Connecting the Memory Extension Unit
+
+
-
Type :UG00P-SR
Lot No :XXXXXXX
+
M
n
O
2
-
L
i
C
E
L
L
3
V
O
L
T
S
J
A
P
A
N
SANYO
See operating or maintenance
instruction for type of
battery to be used.
Battery replacement.
Type :UG00P-SR
Lot No :XXXXXXX
S
e
e
o
p
e
r
a
t
i
n
g
o
r
m
a
i
n
t
e
n
a
n
c
e
i
n
s
t
r
u
c
t
i
o
n
f
o
r
t
y
p
e
o
f
b
a
t
t
e
r
y
t
o
b
e
u
s
e
d
.
B
a
t
t
e
r
y
r
e
p
l
a
c
e
m
e
n
t
.
CR2430
(Caution seal)
Write the date 5 years from today.
-
T
y
p
e
:
U
G
0
0
P
-
S
R
L
o
t
N
o
:
X
X
X
X
X
X
X
CR2430
+
M
n
O
2
-
L
i
C
E
L
L
3
V
O
L
T
S
J
A
P
A
N
SANYO
+
M
n
O
2
-
L
i
C
E
L
L
3
V
O
L
T
S
J
A
P
A
N
SANYO
CR2430
+
“+” (plus) side
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
00000000000 00
MSB LSB
$s167
0: Uninstalled
1: Expansion memory (2M)
2: Expansion memory (4M)
3: SRAM + Clock cassette
Reserved for memory cassette data
(set to 0 (zero))
Reserved for
memory cassette
data (set to 0 (zero))
1: Battery abnormal (needs to be replaced)
Replacement battery for UG00P-SR, UG221P-SR UG00P-BT
Name Type Remarks
Coin type lithium primary battery
About the Battery for UGxxP-SR
To set the battery in the SRAM cassette, use the following procedure:
1. With the “+” (plus) side of the battery faced up, set the battery in the socket of the SRAM cassette.
To set the battery, insert the battery first in the “+” (plus) side of the
SRAM cassette, and then insert it also in the “
-
” (minus) side while
pushing toward the “+” side.
2. Write the date (year, month, day) 5 years from today in the “Next date to
replace battery” field on the attached “Caution” seal, and stick the seal
on the cassette, according to the following figure:
*
The life of the battery for the SRAM cassette is approximately 5 years at 25°C. When the
battery voltage drops, 4th bit of address $s167 in the POD internal memory turns ON to prompt
you to replace the battery. In such case, replace the battery as early as possible.
Precautions for Using the UGxxP-SR
About battery replacement
Before replacing the battery, be sure to make backup files of the data stored in the UGxxP-SR from the
screen development editor. For the backing up procedure, refer to the User's Manual <Operation>
(FEH375).
Adapted version
To use the UGxxP-SR, the versions of the POD main unit and the screen development editor must be the
following:
POD main unit and program version: 1.200 or newerFont data version: 1.100/1.090/1.000 or newer
Screen development editor (UG00S-CW): 2.4.0.0 or newer
About the replacement battery
The following replacement battery is prepared: