Filter
Top Products
32
a My external receiver does not display the programme
number
During installation, the external receiver will be switched to a
different programme number. If the receiver does not display the
programme number, you must check the 'Video window' (left top
corner in the GUIDE Plus+
®
system) to see whether switching has
taken place.
- Select on the DVD-Recorder the socket where the receiver is connected
using CHANNEL q , CHANNEL r (e.g. EXT2for EXT2
AUX-I/O )
- Please check the TV show in the 'Video window' in the left top corner
of the screen.
- Check whether the picture changes during the next step ( OK button).
4 Read the information on the screen carefully.
Confirm with OK .
P The DVD recorder will now attempt to use the G-Link
connection on the external receiver to select a different
programme number (e.g.12). This programme number
depends on your external receiver.
5 Has the external receiver been switched to the programme
number displayed on the screen?
If this is the case, select 'YES'.
If no switching has taken place, select 'NO'.
a My external receiver has not switched to the other
programme number.
- Check that the external receiver is connected and switched on.
- Check the connection and position of the G-LINK transmitter.
- For another attempt with a new code of the chosen brand, select 'NO'.
- Confirm with OK on the remote control.
- If the receiver has not switched yet, select 'NO' again and confirm with
OK . It may take several attempts for a receiver brand.
If you return to the setup screen after confirming 'NO', your receiver
may not have been installed. Check the connections again.
- Tune your external receiver to the TV channel which transmits the
GUIDE Plus+
®
data (see table in the section 'General information'). If
this TV channel is available at the internal tuner of the DVD-recorder,
select this channel.
- Wait till the GUIDE Plus+
®
data is loaded (24 hours) and try the
switch over again.
The control data of the external receivers are automatically updated
(completed) via the GUIDE Plus+
®
system. This is done through the
aerial, the cable, or the external receiver. You do not need to bring the
device to a service centre.
- If your receiver still does not switch, note the type and manufacturer of
your external receiver and call the customer support service in your
country. You will find the telephone number on the back of this
instruction manual.
6 Your external receiver has now been installed.
7 Press OK to return to the setup overview.
a I want to install additional external receivers
When installing additional external receivers, please observe the
following: The external receiver which is controlled by the G-LINK
transmitter must be below the other additional receivers. The
IR(infrared) remote control signal is reflected diagonally upwards and
can therefore be used to control additional external receivers which
are on top.
Finalise setup
Setup Home
PressAorBtoselect.ThenpressOKtoconfirm.
Setup
Chooseitemtosetup:
Language English
Country UnitedKingdom
Postalcode XXXXX
Externalreceiver1 None
Externalreceiver2 None
Externalreceiver3 None
1 Check the settings shown on the screen.
If the settings are not correct, choose the line in which you want
to change the settings and confirm with OK .
2 Press the green function button to leave the screen.
O If you want to view a demonstration of the GUIDE Plus+
®
system select 'View Demo' with B and confirm with OK .
If you start the demo, programmed recordings can be deleted.
O If you do not want to see the demonstration of the GUIDE
Plus+
®
system, end using GUIDE/TV .
3 This completes the set-up process for the GUIDE Plus+
®
system.
4 Switch the DVD-recorder to the TV channel which transmits the
GUIDE Plus+
®
data. The right TV-channel for your country you
will in the table in the chapter 'The GUIDE Plus+
®
system' in the
section 'General information'.
Leave the DVD recorder switched on during the night to load the
GUIDE Plus+
®
data.
The information will be available in the next 24 hours.
5 If data are available check in the 'Editor' screen that the TV
channel which transmits the GUIDE Plus+
®
data is allocated to the
right programme number. Change the programme number if
necessary.
The GUIDE Plus+® System