Filter
Top Products
77
Items in the Extended Setup Menu
Chapter 9 Setup Menus
Items 900 to 999: Settings for digital processing
Item
number
Item name Settings
901 VIDEO OUTPUT DATA Set the bit length for SD-SDI video output data.
8bit: Set the bit length to 8 bits.
[10bit]: Set the bit length to 10 bits.
It is recommended that you select the optimal setting for the device to which you are
going to connect this unit.
920 SD-SDI RP188 ATC
CONTROL
Select whether or not to add information to the SDI output.
OFF: Select whether to add (ON), or not (OFF).
[ON]: Add RP-188 timecode data.
921 ASPECT FLAG Add the 16:9/Squeeze identification signal specified by ARIB TR-B17 to the down-
converted SD output when an HDCAM tape is played. When an SD tape is played,
the 16:9/Squeeze identification signal is detected, and switching the up-converter
mode is set.
[OFF]: The 16:9/Squeeze identification signal is not added to the down-converted
SD output from the HD signal. When an SD tape is played, the up-converter
mode depends on the setting for setup menu item 950 independent of the
existence of the identification signal on the tape.
ON: The 16:9/Squeeze identification signal is added to the down-converted SD
output in squeeze mode from the HD signal. When an SD tape is played, the
identification signal on the tape is detected, and the up-converter mode is
automatically selected. If the identification signal on the tape is not detected, the
up-converter mode depends on the setting for setup menu item 950.
930 DOWN CONVERTER MODE
(DC)
Select the down-converter mode.
[CROP]: Select the edge-crop mode.
L-BOX: Select the letter box mode.
SQUEZ: Select the squeeze mode.
931 DOWN CONVERTER
LETTER BOX MODE (DC)
Select the aspect ratio of the down-converter output when menu item 930 is set to
LETTER BOX.
[16:9]: Set the aspect ratio of the HD-SD converter output to 16:9.
14:9: Set the aspect ratio of the HD-SD converter output to 14:9.
13:9: Set the aspect ratio of the HD-SD converter output to 13:9.
932 H CROP POSITION (DC) Adjust the H-crop (the horizontal position when cropping in the edge crop mode) of
the down converter output when menu item 930 is set to EDGE-CROP.
–120 to [0] to 120
934 CROSS COLOR (DC) Adjust the down-converter cross color.
0 to [8] to 15
935 DETAIL GAIN (DC) Adjust the down-converter image enhancer, the sharpness of edge emphasis.
0 to [20H] to 7FH
936 LIMITER (DC) Adjust the down-converter image enhancer, the maximum detail level added to
emphasize the original signal.
0 to [20H] to 3FH
937 CRISP THRESHOLD (DC) Adjust the down-converter image enhancer, the threshold amplitude at which low
amplitude signals are not emphasized.
[0] to FH
938 LEVEL DEPEND
THRESHOLD (DC)
Adjust the down-converter image enhancer. Set the luminance range for edge
enhancement.
0 to [8] to FH
939 H DETAIL FREQUENCY (DC) Adjust the down-converter image enhancer. Set the central frequency for edge
enhancement.
2.6MHz to 3.4MHz to [3.9MHz] to 4.6MHz
940 H/V RATIO (DC) Adjust the down-converter image enhancer. Set the horizontal/vertical ratio for edge
enhancement.
0 to [3] to 7
941 GAMMA LEVEL (DC) Adjust the down-converter image enhancer, the slope of the correction curve.
0 to [80H] to 100H
942 V FILTER SELECT Set the vertical interpolation filter coefficient for down-converter output.
The vertical resolution increases as the setting grows larger.
[1] to 3