Filter
Top Products
19
EN
Introduction Connections Basic Setup Playback
Editing
Others
Function Setup
Recording
Connections
Connecting to a TV
Connect the unit to a TV after considering the
capabilities of your existing equipment.
Before installation, plug off your TV and this unit.
Using the Scart socket
1 Make a connection for the TV signal.
Depending on the TV signal’s
situation, choose one of following
methods (A-C).
A: Receiving DVB-T signal:
If you are in a area that DVB-T signals are available,
connect the antenna or cable to the ANTENNA IN
(DVB-T) jack of this unit, then connect the ANTENNA
OUT (DVB-T) jack of this unit to the Aerial jack of your
TV. Use the supplied RF cable.
B: Receiving ANALOG signal:
If you are in a area that DVB-T signals are not
available, connect the antenna or cable to the
ANTENNA IN (ANALOG) jack of this unit, then
connect the ANTENNA OUT (ANALOG) jack of this
unit to the Aerial jack of your TV. Use the supplied
RF cable.
C: Receiving both DVB-T and ANALOG signal:
If you need to receive both DVB-T and ANALOG
signal (for hotels that send out cable and DVB-T
signals together etc.), connect the antenna or cable to
the ANTENNA IN (DVB-T) jack of this unit, and
connect the ANTENNA OUT (DVB-T) jack to the
ANTENNA IN (ANALOG) jack of this unit, then
connect the ANTENNA OUT (ANALOG) jack to the
Aerial jack of your TV.
2 After you made a connection for the
TV signal, connect AV1 (TV) Scart
socket of this unit to the Scart
socket of your TV. Use a
commercially available Scart cable.
Note
• If your TV does not have a Scart socket, use a
commercially available Scart adaptor or Scart/RCA
cable to connect.
• Connect this unit directly to the TV. If the AV cables
are connected to a VCR, pictures may be distorted
due to the copy protection system.
• When changing the “Video Out” setting (“SCART
(RGB)”, “Component Interlace (I)” or “Component
Progressive (P)”), connect to the corresponding jack
on the TV. If the setting is changed, for example, to
“Component Interlace (I)” or “Component
Progressive (P)” while the scart cable is connected
to the TV, a distorted video signal may be output.
Connections
ANAL
O
AUDI O
O
COMPONENT
VIDEO OUTPUT
ANALOGDVB-T
OUT
IN
ANTENNA
P
B
/C
B
P
R
/C
R
Y
Cable
Signal
Antenna
RF cable
(supplied)
RF cable
(not
supplied)
To Aerial jack of your TV
or
ANAL
O
AUDI O
O
COMPONENT
VIDEO OUTPUT
ANALOGDVB-T
OUT
IN
ANTENNA
PB/CB
PR/CR
Y
Cable
Signal
Antenna
RF cable
(supplied)
RF cable
(not supplied)
To Aerial jack of your TV
or
ANAL
O
AUDIO
O
COMPONENT
VIDEO OUTPUT
ANALOGDVB-T
OUT
IN
ANTENNA
P
B
/C
B
P
R
/C
R
Y
Cable
Signal
Antenna
RF cable
(not supplied)
RF cable
(supplied)
To Aerial jack of your TV
or
RF cable (not supplied)
AV2
(
DECODER
)
AV1
(
TV
)
ANALOG
AUDIO OUT
N
T
P
UT
L
R
COAXIAL
DIGITAL AUDIO OUTPUT
PCM/BITSTREAM
HDMI OUT
Scart cable
(not supplied)
Audio/Video cable
(not supplied)
Scart/RCA
cable
(not supplied)
Scart adaptor
(not supplied)
or
or
E7J70BD_EN.book Page 19 Monday, May 7, 2007 3:31 PM