Filter
Top Products
39
EN
Introduction Connections Basic Setup Playback
Editing
Others
Function Setup
Recording
Timer Recording
You can set the unit to record up to 12 programmes,
up to a month in advance. Daily or weekly programme
recordings are also available.
• Be sure to set the clock before entering a timer
programming.
Insert a recordable disc.
1 In stop mode, press [TIMER PROG.].
Timer Programming list will appear.
2 Select “New Program” using
[U / D], then press [ENTER/OK].
• If there are 7 programmes or more, use
[SKIP B / F] to turn the page.
3 Enter the date using [U / D], then
press [P].
Each time you press [D] at the current date, the
timer recording date will change as follows.
e.g., 1st January
4 Enter the time to start and to end
using [U / D], then press [P].
5 Select the channel number to record
using [U / D], then press [P].
To record from the external input, select “AV1”,
“AV2”, or “AV3”.
6 Select the recording mode using
[U / D], then press [P].
Refer to “Recording Mode” on page 32.
7 For DVB channel recording:
Select “STTL” to “ON” or “OFF”
using [U / D].
If you set “STTL” to “ON”, subtitle will be recorded
too.
• When analogue channel is selected, “PDC” will
be displayed instead of “STTL”.
For analogue channel recording:
Select “PDC” to “ON” or “OFF”
using [U / D].
Refer to “PDC (Programme Delivery Control)” on
page 40.
• When DVB channel is selected, “STTL” will be
displayed instead of “PDC”.
8 Press [ENTER/OK] when all
information required is entered.
Your programme setting is stored.
• To set another programme, repeat steps 2 to 8.
• To exit, press [TIMER PROG].
• When 2 or more programmes are overlapped,
“Timer program overlapped” appears, and the
overlapped programme will be displayed in blue.
To correct the timer programme, refer to
“Checking, Cancelling or Correcting the Timer
Programming Information” on page 40.
9 Press [ ON / STANDBY] to set a
timer programming.
The icon will appear on the front panel display
and the unit enters to the timer-standby mode.
Note
• If you have not set the clock, the clock setting
window will appear instead of the Timer
Programming list. Continue from step 4 in “Manual
Clock Setting” on page 31 before programming the
timer.
•Press [L / P] to move the cursor in the Timer
Programming list.
• Cancel the timer-standby mode by pressing
[ ON / STANDBY] before operation. When
finished operating, press [ ON / STANDBY] to
resume the timer-standby mode.
DVD-RWDVD-RW
Video
DVD-RWDVD-RW
VR
DVD-RDVD-R D
D
VD+R
VD+R
W
W
DVD+RW
D
D
VD+R
VD+R
DVD+R
Timer Programming
1/1
0:00 THU 06/12
Date
06/12
07/12
Start
7:00
9:00
End
9:00
9:30
CH
18
190
New Program
STTL
PDC
Daily
M-F
(Mon.-Fri.)
01/01
31/01
W-SAT
W-FRI
W-SUN
Timer Programming
1/1
Date
CH
01/01
901
SP 2:00
Mode
Start
SP
- - : - -
PDC
OFF
End
- - : - -
0:00 THU 06/12
Timer Programming
1/1
Date
06/12
07/12
07/12
Start
7:00
9:00
17:00
End
9:00
9:30
18:00
CH
18
190
901
New Program
0:00 THU 06/12
STTL
PDC
E7J70BD_EN.book Page 39 Monday, May 7, 2007 3:31 PM