Toshiba D-R17DTKB DVR User Manual


 
40
EN
PDC (Programme Delivery Control)
Programme Delivery Control (PDC) assures that the
TV programmes you have programmed for timer
recording are recorded exactly from beginning to end,
even if the actual broadcasting time differs from the
scheduled time due to a delayed start or extension of
the programme duration. Furthermore, if a
programme is interrupted, the recording will also be
interrupted automatically and resumed when the
programme starts again.
If the PDC signal drops out because the broadcast
signal is weak, or if a broadcasting station does not
transmit a regular PDC signal, the timer recording is
performed in normal mode (without PDC) even if it
was programmed for PDC. If the starting time of the
PDC timer recording is between 0:00 and 3:59 on a
given day, the PDC function will operate from 20:00
on the previous day to 4:00 on the next day. If the
starting time of the PDC timer recording is between
4:00 and 23:59 on a given day, the PDC function will
operate from 0:00 on the given day to 4:00 on the
next day. This means that if the relevant programme
is broadcasted within this period, it is recorded
correctly. If the timer is not programmed correctly, the
incorrect timer setting stays in effect unless you
cancel it. To cancel an incorrect timer setting, refer to
“Checking, Cancelling or Correcting the Timer
Programming Information” below.
Note
This feature is only available for analogue channels.
Checking, Cancelling or Correcting
the Timer Programming Information
1 Press [ ON / STANDBY].
2 Press [TIMER PROG.].
Timer Programming list will appear.
3 Check the information on the list you
want to edit.
4 A) To delete the timer programme:
1) Select the programme you want to delete using
[U / D], then press [ENTER/OK].
2) Select “Delete” using [U / D], then press
[ENTER/OK].
Confirmation window will appear.
3) Select “Yes” using [U / D], then press
[ENTER/OK].
B) To correct the timer programme:
1) Select the programme you want to correct
using [U / D], then press [ENTER/OK].
2) Select “Program Change” using [U / D], then
press [ENTER/OK].
3) Correct the timer programme by using
[U / D / L / P], then press [ENTER/OK].
5 Press [TIMER PROG.] to exit.
6 Press [ ON / STANDBY] to return
to the timer-standby mode.
To check the timer programming in process
Press [TIMER PROG.].
Note
If a timer recording is proceeding, that programme is
highlighted in red. In such a case, you cannot select
any other programmes.
To Stop the Timer Recording in
Progress
On the front panel of the unit, press
[
S (STOP)
] to stop the recording.
Note
[STOP S] on the remote control is not effective.
If the Timer Programming Did Not
Complete Correctly
The error number appears on the Timer Programming
list.
The error programme will be displayed in grey
with an asterisk and have an error number.
The error numbers indicate:
E1–E22,
E37–E39:Recording error
E23–E24:Unrecordable disc
E25 :•Copy prohibited programme
•Cannot record because of the NTSC /
PAL-60 signal is received.
E26–E28: Copy prohibited programme
E29 :Disc protected
E30 :Disc full
E31 :Already recorded 99 titles (Video
mode)
E32 :Already recorded 99 titles (VR mode)
E33 :Already recorded 999 chapters
E34 :No space for Control Information
E35 :PCA (Power Calibration Area) full
E36 :Already finalised Video format disc
E40 :•There are some unrecorded parts due
the overlapped timer programmes.
•Recording did not start at the start
time.
E41 :Power failure
E42 :No disc
E43 :Already 49 titles recorded (+VR mode)
E44 :Already 254 chapters recorded
(+VR mode)
E45 :Copy prohibited programme
E46 :It is impossible to record additionally on
a disc recorded by other units when
setting “Make Recording Compatible”
to “OFF”. (+VR mode)
The error programme will be deleted once you
check the error in the programme list, or once you
cancel the timer-standby mode and re-enter it.
Timer Programming
1/1
E40
Date
06/12
Start
7:00
End
9:00
CH
901
New Program
0:00 THU 06/12
STTL
PDC
E7J70BD_EN.book Page 40 Monday, May 7, 2007 3:31 PM