Filter
Top Products
36
Setup menus (continued)
SYSTEM
“_____” indicates the factory setting.
No./Item Description of setting
05
ENCODER
SEL
For setting whether to perform the various
adjustments for the video output signals using this
VTR or using an external encoder remote controller.
0001 LOCAL
:
The various adjustments for the video output
signals are performed using this VTR.
0002 BOTH :
The various adjustments for the video output
signals are performed using both this VTR and an
external encoder remote controller.
<Notes>
z For video adjustments, refer to “Video output signal
adjustments” (page 35).
z If the signals are adjusted with the external
encoder remote controller, the adjusted values are
reflected in the setup menu. However, the adjusted
numerical values will not be stored unless about 1
minute has elapsed after completion of the
adjustment operation. If the unit is turned off after
executing the adjustments with the external
encoder remote controller, it is necessary to wait
about 1 minute before turning off the power.
z Settings in this menu are not effective for the
IEEE1394 digital output.
06
V LEVEL
CTRL
For selecting what is to be controlled when the video
output level is to be adjusted by an external encoder
remote controller.
0000 HD :
The HD video output level can be adjusted.
0001 SD :
The SD video output level can be adjusted.
0002 BOTH :
Both the HD and SD video output levels can be
adjusted.
12
SYS H
(HD)
For adjusting the system phase of the HD SDI output
signals. (in 13.5 ns increments).
– :Phase advances.
+ :Phase delays.
0000 –1100
: :
1100
0
: :
2200 1100
<Notes>
z When menu item No. 25 SYSTEM FREQ is set to
50i/25P, 25 (HD), 25(SD), 50 (HD) or 50 (SD), the
setting range is from –1320 - 0
- 1320.
z When menu item No. 25 SYSTEM FREQ is set to
23/24, the setting range is from –1375 - 0
- 1375.
14
SYS SC
(SD)
For adjusting the system phase of the analog
composite output and SD SDI output signals (total
variable range of over ±180 degrees).
– :Phase advances.
+ :Phase delays.
0000 –108
: :
0108
0
: :
0216 108
15
VO SYS H
(SD)
For adjusting the system phase of the analog
composite output signals (in 37 ns increments).
– :Phase advances.
+ :Phase delays.
0000 –858
: :
0858
0
: :
1716 858
<Note>
The setting range is –864 to 0 to 864 when 50i/25P,
25 (HD) or 25 (SD) is selected as the menu item
No.25 SYSTEM FREQ setting.
No./Item Description of setting
16
SD SYS H
(SD)
For adjusting the system phase of the SD SDI output
signals (in 37 ns increments).
– :Phase advances.
+ :Phase delays.
0000 –858
: :
0858
0
: :
1716 858
<Note>
The setting range is –864 to 0 to 864 when 50i/25P,
25 (HD) or 25 (SD) is selected as the menu item
No.25 SYSTEM FREQ setting.
18
SCH
COAR
(SD)
For adjusting the SCH (sub-carrier to horizontal)
phase of the analog composite output signals (4
positions in 90-degree increments).
The SC phase changes, and the H phase remains
unchanged.
0000 0
0001 90
0002 180
0003 270
19
SCH FINE
(SD)
For adjusting the SCH (sub-carrier to horizontal)
phase of the analog composite output signals
(variable range of over ±45 degrees).
The SC phase changes, and the H phase remains
unchanged.
A range of ±180 degrees is covered by using this
setting in combination with item No.18 SCH COAR
(SD).
0000 –32
: :
0032
0
: :
0064 32
20
AV
PHASE
For adjusting the phase of the AUDIO output signals
in relation to the video output signals (in 20.8 µs
increments).
– :Audio phase against image advance.
+ :Audio phase against image delay.
0000 –100
: :
0100
0
: :
0200 100