Filter
Top Products
42
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
This item is used to copy the data in the main device to the
copy device.
Copy Data to Copy A Drive/Set Copy A
Drive
This item is used to copy the data by specifying the start
and end points of copying. The points are specified by the
date and time or the book mark. This function is useful for
copying the data of the short period of time.
• Before executing the copy, make sure that the Copy
A device is connected and set in the <Add/Remove
HDD Device> and <Add/Remove DVD/CD Drive>
(System Menu
Memory) correctly.
Copy Data to Copy A Drive
Set Copy A Drive
Range of Copy
1
2
3
User Menu
Copy
2
steps
1, 2
step
3
steps
4, 5
step1. Set the camera number to be copied.
• The button function changes between “All Off”
and “All On” each time you select this button. You
can switch on and off for all the cameras easily
by using this button.
• The picture is not copied when there is no
recorded picture of the set camera number or
time.
step2. Select “Other settings” and then set the detailed
settings.
From: Sets the area which contains the data to be
copied. The available setting items are “Normal,”
“Alarm,” and “LPA.”
To: Sets the group number to which the data is
copied. The available setting items are “Group 1”
to “Group 5.”
Copy Data: Sets the data to be copied. The
available setting items are “Alarm” and “All.”
Overwrite: Selects whether to overwrite the existed
data or not.
Auto Eject: Selects whether to eject media
automatically when the copy is over.
•“Alarm” appears for “From” and “Copy Data” when
“Alarm Recording Area” (System
Menu Memory Data Management Setting for Main
Memory Change Partition Setting) is set to other than
“0 %.”
•“LPA” appears for “From” when “Long Pre-Alarm Area”
(System Menu
Memory Data Management Setting
for Main Memory Change Partition Setting) is set to
other than “0 %.”
Copy User Menu
• When copying the data to DVD and setting “Overwrite”
to “On,” the unit clears the existed data of the disk
before overwriting the data. Note that clearing the data
takes about 30 to 40 minutes.
step3. Set the start, start/end, or end points of the copy by
specifying the date and time or the book mark.
Start: Sets only the start point of the copy.
Start/End: Sets the start and end points of the copy.
End: Sets only the end point of the copy.
• To set the point using the book mark, select
“Bookmark” and then select the desired book
mark number.
• To copy the oldest recorded time, select “Copy
Start Time.” To copy the latest recorded time,
select “Copy End Time.”
step4. Select “Calculate” to calculate the capacity of the
data to be copied.
• When using “End,” the copy cannot be executed
unless the calculation of the capacity of the data to
be copied is completed.
• When using “Start” or “Start/End” and executing the
copy without calculating the capacity of the data to
be copied, the progress or the time of the copy may
not be displayed correctly because the unit cannot
specify the capacity of the data to be copied.
step5. Select “Execute.”
• The copy starts.
• To stop the copy manually, select “Cancel” in the
progress screen. The data which has been copied
before cancelling is copied.
Copy Data to Copy B Drive/Set Copy B
Drive
This item is used to copy the data by specifying only the
start point of copying. The point is specified by the date
and time. The copy continues until the end point of the
recorded data reaches or the media to be copied becomes
full unless the copy is stopped manually (when “FIFO
Overwrite” is set to “Off”). This function is useful for making
backup of the recorded data.
• Before executing the copy, make sure that the Copy
B device is connected and set in the <Add/Remove
HDD Device> and <Add/Remove DVD/CD Drive>
(System Menu Memory) correctly.
Copy Data to Copy B Drive
Set Copy B Drive
Range of Copy
2
2
4
User Menu
Copy
2
steps
1, 2
step
3
step
4