Mitsubishi Electronics WD-57833 Flat Panel Television User Manual


  Open as PDF
of 96
 
3. TV Connections 19
Wall Outlet Cable (no cable box)
It is very important to connect the incoming cable for 
your primary viewing source to 
ANT 1/MAIN
.
1.  Connect the primary incoming coaxial lead cable to  
ANT 1/MAIN
 on the TV back panel.
2.  For an optional secondary antenna source, connect 
an antenna (or cable) to 
ANT 2/AUX
.
COMPONENT 1
Y Pb Pr (480i/480p/720p/1080i)
COMPONENT 2
RECORD
OUTPUT
OUTPUT
DIGITAL
IR EMITTER
NetCommand
RS-232C
AUDIO
INPUT 1
INPUT 2
HDMI
VIDEO: 480i / 480p / 720p /
1080i / 1080p
W-SVGA, XGA, W-XGA,
AUDIO: LINEAR PCM
PC: VGA, W-VGA, SVGA,
1 (LEFT) ,, 2 (MIDDLE) 3 (RIGHT)
DVI / PC
VIDEO
AUDIO-
AUDIO-
RIGHT
L (MONO)
L (MONO)
INPUT
AVR
AUDIO
AUDIO
OUTPUT
S-VIDEO VIDEO - AUDIO - R
L (MONO)
- AUDIO - R
Y Pb Pr
EMITTER
3D GLASSES
SXGA
IEEE 1394
ANT 2 / AUX
ANT 1 / MAI
N
ANT 2 / AUX
ANT 1 / MAI
N
Figure 4. Wall Outlet Cable
A. For an antenna with flat twin leads
Required:  300-ohm-to-75-ohm transformer.
A1.  For an antenna with flat twin leads, connect the 
300-ohm twin leads to the 300-ohm-to-75-ohm 
transformer.
A2. Push the 75-ohm side of the transformer onto 
ANT
1
 on the TV back panel.
B. For cable or antenna with coaxial lead
Connect the coaxial lead directly to 
ANT 1
 on the 
TV back panel.
COMPONENT 1
Y Pb Pr (480i/480p/720p/1080i)
COMPONENT 2
RECORD
OUTPUT
OUTPUT
DIGITAL
IR EMITTER
NetCommand
RS-232C
AUDIO
INPUT 1
INPUT 2
HDMI
VIDEO: 480i / 480p / 720p /
1080i / 1080p
W-SVGA, XGA, W-XGA,
AUDIO: LINEAR PCM
PC: VGA, W-VGA, SVGA,
1 (LEFT) ,,2 (MIDDLE) 3 (RIGHT)
DVI / PC
VIDEO
AUDIO-
AUDIO-
RIGHT
L (MONO)
L (MONO)
INPUT
AVR
AUDIO
AUDIO
OUTPUT
S-VIDEO VIDEO - AUDIO - R
L (MONO)
- AUDIO - R
Y Pb Pr
EMITTER
3D GLASSES
SXGA
IEEE 1394
ANT 2 / AUX
ANT 1 / MAI
NANT 1 / MAIN
0IN
'MBU5XJO
-FBE
0QUJPOBM0IN
UP0IN
.BUDIJOH5SBOTGPSNFS
0IN
$PBYJBM
$BCMF
#
"
"
57#BDL1BOFM
Figure 6. Connecting a Single Antenna Lead
Antennas with Separate UHF and
VHF Leads
Required:  UHF/VHF combiner
1.   Connect the UHF and VHF antenna leads to the 
UHF/VHF combiner.
2.  Push the combiner onto 
ANT 1/MAIN
 on the TV 
back panel.
COMPONENT 1
Y Pb Pr (480i/480p/720p/1080i)
COMPONENT 2
RECORD
OUTPUT
OUTPUT
DIGITAL
IR EMITTER
NetCommand
RS-232C
AUDIO
INPUT 1
INPUT 2
HDMI
VIDEO: 480i / 480p / 720p /
1080i / 1080p
W-SVGA, XGA, W-XGA,
AUDIO: LINEAR PCM
PC: VGA, W-VGA, SVGA,
1 (LEFT) ,, 2 (MIDDLE) 3 (RIGHT)
DVI / PC
VIDEO
AUDIO-
AUDIO-
RIGHT
L (MONO)
L (MONO)
INPUT
AVR
AUDIO
AUDIO
OUTPUT
S-VIDEO VIDEO - AUDIO - R
L (MONO)
- AUDIO - R
Y Pb Pr
EMITTER
3D GLASSES
SXGA
IEEE 1394
ANT 2 / AUX
ANT 1 / MAINANT 1 / MAIN
#BDL
7JFX
4JEF
7JFX
6)'"OUFOOB
$IBOOFMT
7)'"OUFOOB
$IBOOFMT
0INUP
0IN
$PNCJOFS
'MBU5XJO-FBE
6)'
7)'


5P"/5."*/
57CBDLQBOFM
&YUFSOBM
"OUFOOB
PS$BCMF
Figure 5. Connecting separate UHF and VHF Antennas
Mitsubishi strongly recommends you avoid using
antennas with flat twin leads. Flat twin lead
antenna wires are subject to interference which
may adversely affect the performance of the TV.
We recommend using coaxial antenna cable.
Antenna with a Single Lead
 previous next