Mitsubishi Electronics WD-57833 Flat Panel Television User Manual


 
4. TV Operation and Features 29
Note: To operate other audio/video devices using 
the TV’s remote control:
•  See Appendix D, “Programming the Remote 
Control.”
•  See chapter 6, “NetCommand,” for NetCommand 
IR “Learning” of device keys.
•  For control of IEEE 1394 devices, see chapter 6, 
“NetCommand.”
•  For HDMI devices compatible with the 
TV’s NetCommand for HDMI feature, see 
“NetCommand for HDMI Devices“ on this page.
23.
F1–F4
For devices under NetCommand control:  
Perform NetCommand “Learning” to assign your 
choice of functions to the 
F1
F4
 keys.
For devices operating independently of
NetCommand:  The 
F1
F4
 keys work like the  A, 
B, C, D buttons on some cable boxes, satellite 
receivers, and DVD players.  Program the remote 
control for your equipment and test the keys.  See 
Appendix D, “Programming the Remote Control.”
25. (
PAUSE
):  Freezes a broadcast TV picture when 
no Split Screen image is displayed.  When Split 
Screen is displayed, freezes the sub-picture.
Record/Playback Keys
Use any of these methods to enable the recording and 
playback commands:
•  Program the remote control for your DVR, VCR, or 
DVD player/recorder and set the slide switch to 
VCR
, 
DVD
,
CABLE/SAT
, or 
AUDIO
 as appropriate.
•  Perform NetCommand IR “learning” for the device.
•  For control of IEEE 1394 devices, see chapter 6, 
“NetCommand.”
•  Check HDMI devices for compatibility with the TV’s 
NetCommand for HDMI feature (see below).
24.
(
RECORD
):
 Records with a VCR or DVR.
25. (
PAUSE
):  Pauses a VCR, DVR, or DVD.  See 
above for use during TV viewing.
26.
(
STOP
):  Stops play of a VCR, DVR, or DVD.
27.
(
REVERSE
):  Rewinds a VCR.  Reverse scans a 
DVR or DVD.
28. (
PLAY
):  Plays a VCR, DVR, or DVD.
29.
(
FORWARD
):  Fast forwards a VCR.  Forward 
scans a DVR or DVD.
Remote Control, continued
Care of the Remote Control
Use only alkaline batteries.
Be within 20 feet of the equipment.
Do not press two or more buttons at the same time 
unless instructed to do so.
Do not allow unit to get wet or become heated.
Avoid dropping on hard surfaces.
Do not use harsh chemicals to clean.  Use only a 
soft, lightly moistened cloth.
Do not mix old and new batteries.
Resetting the Remote Control
If the slide switch is set to 
TV
 and the TV does not 
respond properly, reset the remote control.
1.  Press and hold 
POWER
 for several seconds until the 
button blinks twice and goes off.
2.  Release the 
POWER
 button.
3.  Press keys 
0 0 9 3 5
 and the 
POWER
 button will blink 
twice when you finish entering the code.  While 
entering the code, pause for a moment between 
each key press to ensure it is recognized.
Low-Battery Indicator
If you press a key and the 
POWER
 key blinks five times, 
replace the remote control’s batteries.
NetCommand for HDMI Devices
The TV’s remote may operate some functions of 
compatible HDMI devices able to receive commands 
through the HDMI cable.  Test your equipment with the 
TV’s remote to find out which commands are sup-
ported.  See below for commands that may be avail-
able, depending on the individual device.  You can add 
commands using NetCommand IR “learning” after con-
necting and placing IR emitters for the devices.
Press 
PLAY
 on the device itself to:
•  Turn on the TV if not already on
•  Switch to the device (no need to display the Input
Selection menu)
•  Begin play of the device
VCR, DVD, and DVR functions that may be available:
Record/
Playback
Menu
Navigation
Channel Tuning Other
  
CH
 / 
GUIDE
ENTER
Digits 
0–9
, 
CANCEL
F1
 (content)
CANCEL
 (to cancel)
ENTER MENU