Mitsubishi WD-52631 Projection Television User Manual


  Open as PDF
of 108
 
Chapter 5. Operating Other Devices with the Remote Control 63
IMPORTANT
You may need to reprogram the remote
control after changing the batteries.
Programming the Remote Control
Method 1: Code Entry
1. Movetheslideswitchatthetopoftheremotetothe
positionfortheproductyouwanttocontrol.Referto
thetablebelow.Onlyoneofeachdevicetypecanbe
controlledineachslide-switchposition.
Switch Position Affected Device
CABLE/SAT
CableBox
DTVReceiver
SatelliteReceiver
VCR
VCR
DVR
LaserDiscPlayer
DVDPlayer/Recorder
DVD
DVDPlayer/Recorder
DVR
LaserDiscPlayer
VCR
AUDIO
A/VReceiver
AudioAmplifier
CDPlayer*
2. Pressandhold
POWER
ontheremotecontrolforseveral
secondsuntilthebuttonblinkstwiceandgoesoff.
3. Releasethe
POWER
button.
4. Enterthefirstfive-digitcodelistedforyourequipment.
• The
POWER
buttonblinkstwicewhenyoustartto
enterthecodeandthenonceforeachadditional
keypress.
• The
POWER
buttonblinkstwicewhenyoufinish
enteringavalidcode.
• Movetheslideswitchtoanotherpositionifyou
needtostartoverorwishtoexitprogramming
mode.
5. Pointtheremotecontrolattheequipmentandpress
POWER
. Iftheproducthasnopoweron/offfunction,
pressadifferentkey,suchas (
PLAY
), (
STOP
),
VOL
,or
MUTE.
• Iftheequipmentresponds,theremotecontrolis
properlyprogrammedtooperatetheequipment.
• Iftheequipmentdoesnotrespond,repeatsteps
2–4withthenextfive-digitcodelistedforyour
equipment.
6. Onceyouhavefoundthecorrectcode,writeitinthe
spacebelowforfuturereference.
Switch Position
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
Method 2: Code Search
Inthismethodofprogramming,youstepthroughthe
remotecontrol’sinternalcodelibrarytofindthecorrect
codeforyourA/Vproduct.
1. Movetheslideswitchatthetopoftheremotecontrol
tothecorrectpositionfortheproduct.Seethetable
under“Method1.”
2. Pressandhold
POWER
ontheremotecontrolforseveral
secondsuntilthebuttonblinkstwiceandgoesoff.
3. Presskeys
9 9 1
4. Pressthenumber
1
,
2
,or
3
dependingontheslide-
switchpositionandthetablebelow.
Switch Position Number
CABLE/SAT
1
DVD, VCR
2
AUDIO
3
5. Press
CH
and
POWER
repeatedlyuntiltheproduct
respondsbypoweringonoroff.Youcanpress
CH
tomovebackwardthroughthecodelibraryifneeded.
NOTE: Iftheproducthasnopoweron/offfunction,check
foraresponseusingadifferentfunction.Press
(
PLAY
), (
STOP
),
VOL
,or
MUTE
andthenre-
peatedlypress
CH
/ tocheckforaresponse.
6. Whentheproductresponds,press
ENTER
tosetthe
code.
Code Verification
Todeterminethecodeprogrammedforanypositionof
theslideswitch:
1. Movetheslideswitchtothepositionyouwishto
verify.
2. Pressandhold
POWER
ontheremotecontrolforseveral
secondsuntilthebuttonblinkstwiceandgoesoff.
3. Presskeys
9 9 0
4. Press
1
andcounttheblinksofthepowerbutton.
Writedownthenumberofblinksasthefirstdigitof
thecode.
5. Repeatstep4forthesecond,third,fourth,andfifth
digitsofthecode.
 previous next