Filter
Top Products
ALARM REC MODE SET SETTING
4
Turn the shuttle dial clockwise, use the jog dial to set the
recording method (example: “FRAME”), and then turn the
shuttle dial clockwise.
The cursor moves to AUDIO RECORDING.
Note:
•
When FRAME/FIELD RECORDING is selected, the recording
speed appears in REC CYCLE and the maximum number of
recordings appears after it in brackets.
=> (30721 ALARMS CAN BE RECORDED)
•
The field and frame recording speeds vary depending on the
PICTURE QUALITY setting. Refer to the Recording speed table
for details. (See page 10.)
5
Turn the shuttle dial clockwise, use the jog dial to set
audio recording (example: “ON”), and then turn the
shuttle dial.
The cursor moves to ALARM RECORDING.
Note:
•
Audio recording can be set when the REC CYCLE setting is
0.12 SEC (FIELD) or 0.24 SEC (FRAME) or more.
•
When set to “ON”, the letter “A” (audio recording indicator)
appears in front of the REC CYCLE recording speed, and the
maximum number of recordings appears after it in brackets.
=> (30200 ALARMS CAN BE RECORDED)
6
Turn the shuttle dial clockwise, use the jog dial to set
alarm recording mode (example: “MODE1”), and then turn
the shuttle dial.
The cursor moves to REC CYCLE.
Display example: Alarm recording settings
•
OFF: Alarm recording is not carried out.
•
MODE1: Alarm recording is always carried out regardless
of the timer recording settings.
•
MODE2: Alarm recording is only carried out when timer
recording is in progress.
•
MODE3: Alarm recording is only carried out when timer
recording is not in progress
•
MODE4: Alarm recording is carried out only during the
times set by the timer. This cannot be used for
normal recording.
Note: If alarm recording is set to a setting such as MODE1,
PRE-ALARM RECORDING setting will be enabled (“***”
will change to “OFF”).
7
Turn the shuttle dial clockwise, use the jog dial to set the
recording speed (example: “0.16”), and then turn the
shuttle dial.
DURATION of “1SEC” flashes.
Note: When the recording speed is selected, the maximum number
of recordings appears after it in brackets.
=> (20480 ALARMS CAN BE RECORDED)
8
Use the jog dial to set the recording time duration
(example: “5”), and then turn the shuttle dial.
The cursor moves to PRE-ALARM RECORDING.
9
Press the EXIT/OSD button.
The display returns to the normal screen.
Alarm settings appear in the operating display section. When
an alarm is triggered, the number of alarms is displayed.
Note: If another alarm occurs while alarm recording is in progress,
alarm recording continues with images for the second alarm
being recorded from the point where the second alarm
occurred.
If several alarms have occurred at the same time, they are
treated as a single alarm until the alarms stop.
<ALARM REC MODE SET>
PICTURE QUALITY : SUPER FINE
FRAME/FIELD RECORDING : FRAME
AUDIO RECORDING : OFF
ALARM RECORDING : OFF
REC CYCLE : 0.24SEC. DURATION: 1SEC
PRE-ALARM RECORDING : ¤¤¤
<ALARM REC MODE SET>
PICTURE QUALITY : SUPER FINE
FRAME/FIELD RECORDING : FRAME
AUDIO RECORDING : ON
ALARM RECORDING : OFF
REC CYCLE : A0.24SEC. DURATION: 1SEC
PRE-ALARM RECORDING : ¤¤¤
REC CYCLE : ¤¤¤ SEC. DURATION: ¤¤¤
<ALARM REC MODE SET>
PICTURE QUALITY : SUPER FINE
FRAME/FIELD RECORDING : FRAME
AUDIO RECORDING : ON
ALARM RECORDING : MODE1
REC CYCLE : A0.16SEC. DURATION: 5SEC
PRE-ALARM RECORDING : OFF
REC CYCLE :
¤¤¤
SEC. DURATION:
¤¤¤
=> (04026 ALARMS CAN BE RECORDED)
ALARM TRIGGER : ALARM
MOTION SENSOR ->
EXIT/OSD
01-01-01 ALARM 0000
05:53:44 SF 0.16SEC
English
53