Filter
Top Products
EN-5
WARNING:
Unplug immediately if there is something wrong with your
projector.
Do not operate if smoke, strange noise or odor comes out of your
projector. It might cause re or electric shock. In this case, unplug
immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An inadvertent
contact may result in an electric shock. Except as specically
explained in the User Manual do not attempt to service this
product by yourself. Please contact your dealer when you want to
x, adjust or inspect the projector.
Do not modify this equipment.
It can lead to re or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged, unplug
the projector and contact your dealer for inspection. It may lead
to re if you keep using the damaged projector.
Do not face the projector lens to the sun.
It can lead to re.
Use correct voltage.
If you use incorrect voltage, it can lead to re.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface only. Please do
not place equipment on unstable surfaces.
Do not look into the lens when it is operating.
It may hurt your eyes. Never let children look into the lens when
it is on.
Do not unplug the power cord during operation.
It can lead to lamp breakage, re, electric shock or other trouble.
It is best to wait for the fan to turn o before turning the main
power o.
Do not touch the air outlet grille and bottom plate, which
become hot.
Do not touch them or put other equipment in front of the air
outlet grille. The air outlet grille and bottom plate, when heated,
may cause injury or damage to other equipment. Also, do not set
the projector on the desk which is easily aected by heat.
Do not look into the air outlet grille when projector is operating.
Heat, dust, etc. may blow out of it and hurt your eyes.
Do not insert your ngers in the space between the lens and the
cabinet.
The lens may shift causing injury or damage to the projector.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the projector,
causing deterioration in the projector quality and re.
Do not use ammable solvents (benzene, thinner, etc.) and
ammable aerosols near the projector.
Flammable substances may ignite causing re or breakdown
because the temperature inside the projector rises very high
while the lamp is illuminating.
Do not use the projector with condensation on it.
It can lead to breakdown or other failure.
Place of installation
For safety’s sake, refrain from setting the projector at any place
subjected to high temperature and high humidity. Please
maintain an operating temperature, humidity, and altitude as
specied below.
• Operating temperature: between +41°F (+5°C) and +95°F
(+35°C)
• Operating humidity: between 30% and 90%
• Never put any heat-producing device under the projector so
that the projector does not overheat.
• Do not attach the projector to a place that is unstable or
subjected to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic eld. Also refrain from installing
near the projector any cable carrying a large current.
• Place the projector on a solid, vibration free surface; otherwise
it may fall, causing serious injury to a child or adult, and
serious damage to the product.
• Do not stand the projector; it may fall, causing serious injury
and damage to the projector.
• Slanting the projector more than ±10°(right and left) or
±10°(front and rear) may cause trouble or explosion of the
lamp.
• Do not place the projector near air-conditioning unit, heater,
or humidier to avoid hot or moist air to the exhaust and
ventilation hole of the projector.
• We don’t recommend using the projector at an altitude of
1500 meters or higher. Use at an altitude of 1500 meters or
higher may aect the projector’s life.
• Do not place the projector in the following places. Otherwise,
a short circuit, heat generation, or melting of the power cord
coating may occur, causing re, electric shock, product failure,
or deformation.
• Outdoors or non air-conditioned place
• Place where a gas such as a hydrogen sulde is generated
(i.e. hot spring)
• Place where there is too much salt such as near the coast
• Plug is used for disconnect device. So the socket-outlet
should be install near the equipment and shall be easily
accessible.
Important safeguards (continued)
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
Changes or modications not expressly approved by Mitsubishi could void the user’s authority to operate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.