Filter
Top Products
31–19
XOTime?, 31–19
XPATtern, 17–20, 23–23, 24–20
Xreference, 35–16
XREFerence?, 35–16
XSEarch, 17–21, 23–24, 24–21
XSTate, 14–11, 17–22, 24–21
XTAG, 17–23, 24–22
XTIMe, 14–12, 23–25
XTIMe?, 31–20
XVOLt, 31–17
YINCrement, 35–17
YINCrement?, 35–17
YORigin, 35–17
YORigin?, 35–17
YREFerence, 35–18
YREFerence?, 35–18
Query errors, 7–5
query program example, 36–22
Query responses, 1–15, 4–4
Question mark, 1–10
QYE, 6–5
R
RANGe, 29–8, 33–6
RANGe command, 25–6
RANGe command/query, 14–9, 16–14,
16–15, 18–8, 20–11, 22–15, 22–16, 23–16
RANGe?, 29–8, 33–6
range_argument, 29–4, 33–3
raw data, 35–6
real-time clock
section data, 26–17
Receive Data (RD), 3–4, 3–5
RECord, 35–12
RECord?, 35–12
Remote, 2–5
Remote enable, 2–5
REMove, 30–9, 30–10
REMove command, 14–10, 15–13, 17–15,
18–9, 21–7, 23–16, 24–14, 25–7
REN, 2–5
REName command, 11–18
REName command/query, 13–8
Request To Send (RTS), 3–5
RESource command/query, 13–9
Response data, 1–20
Responses, 1–16
return X-O marker data, 31–19
returning preamble, 35–11
returning waveform data record, 35–9
RISetime, 32–9
risetime measurement, 32–9
RISetime?, 32–9
RMODe command, 9–18
Root, 4–6
RQC, 6–5
RQS, 6–4
RS-232C, 3–2, 3–10, 5–2
RUNTil, 31–11
RUNTil command/query, 17–15, 17–16,
20–12, 23–17, 24–15
RUNTil?, 31–11
S
sample rate data, 31–12
sampling period, 35–13
SCHart selector, 19–4
SCHart Subsystem, 19–1, 19–3, 19–4,
19–5, 19–6, 19–7
SDC, 2–6
Section data, 26–6
Section data format, 26–4
Section header, 26–6
SELect command, 9–20
Select command tree, 9–21
Selected device clear, 2–6
SEQuence command/query, 16–16, 22–17
Sequential commands, 4–4
Serial poll, 6–7
Service Request Enable Register, 6–4
SET command, 20–13
SETColor command, 9–22
setting logic, 34–10
setting stop condition, 31–11
setting time marker mode, 31–14
setting timebase, 33–5
setting voltage marker mode, 31–15
SETup, 10–11, 26–15
SETup command/query, 10–11, 10–12
SFORmat selector, 15–6
SFORmat Subsystem, 15–1, 15–3, 15–4,
15–5, 15–6, 15–7, 15–8, 15–9, 15–10,
15–11, 15–12, 15–13, 15–14, 15–15, 15–16,
15–17, 15–18
Shortform, 1–11
SHOW, 31–12
Simple commands, 1–8
SKEW command, 12–8
SLAVe command/query, 15–15
SLISt selector, 17–7
SLISt Subsystem, 17–1, 17–3, 17–4, 17–5,
17–6, 17–7, 17–8, 17–9, 17–10, 17–11,
17–12, 17–13, 17–14, 17–15, 17–16, 17–17,
17–18, 17–19, 17–20, 17–21, 17–22, 17–23
slope, 31–5, 34–12
SLOPe?, 34–13
slot_number, 30–4
SOURce, 32–10, 34–13, 35–12
SOURce?, 32–10, 34–13, 35–13
Spaces, 1–7
SPERiod, 35–13
SPERiod command/query, 22–18, 23–18
SPERiod?, 35–13
Square brackets, 4–5
STARt command, 9–23
state analyzer
program example, 36–5
Status, 1–22, 6–2, 8–3
Status byte, 6–6
Status registers, 1–22, 8–3
Status reporting, 6–2
Stop bits, 3–9
STOP command, 9–24
stop condition, 31–11
STORe command/query, 16–17
STORe:CONFig command, 11–19
STRace Command, 16–9
STRigger Command, 16–9
STRigger/STRace Subsystem, 16–1, 16–3,
16–4, 16–5, 16–6, 16–7, 16–8, 16–9, 16–10,
16–11, 16–12, 16–13, 16–14, 16–15, 16–16,
16–17, 16–18, 16–19, 16–20, 16–21, 16–22,
16–23, 16–24
String data, 1–13
String variables, 1–18
STTRace selector, 22–8
Subsystem
ACQuire, 28–1, 28–2, 28–3, 28–4, 28–5
CHANnel, 29–1, 29–2, 29–3, 29–4, 29–5,
29–6, 29–7, 29–8, 29–9
COMPare, 20–2
DISPlay, 30–1, 30–2, 30–3, 30–4, 30–5,
30–6, 30–7, 30–8, 30–9, 30–10
Index
Index–7