Filter
Top Products
99
The following are for the recording rate. When OFF is
selected, images from the selected camera channel will not
be recorded.
OFF/0.1 ips/0.2 ips/0.3 ips/0.4 ips/0.5 ips/1 ips/2 ips/3 ips/5
ips/6 ips/7.5 ips/10 ips/15 ips/30 ips/60 ips
AUTO: Recording rate will be set automatically. (Not possi-
ble for event pre-recording and event post-recording)
Important:
The total recording rates of each camera channels in the
same recording mode must be less than the recording rate
as described in "Recording Rate for Each Recording Mode"
above.
Examples: When selecting "FIELD" for resolution, "15 ips" for
manual recording, "15 ips" for scheduled recording, "30 ips"
for event recording:
Total recording rates of CAM 1 - 16 (manual recording):
less than 15 ips
Total recording rates of CAM 1 - 16 (scheduled recording):
less than 15 ips
Total recording rates of CAM 1 - 16 (event recording): less
than 30 ips
When the total recording rates becomes more than the set
value, the recording mode table will turn red.
Recording mode table
The larger total recording rates between recording rates of
event pre-recording and recording rates of event post-
recording for each camera channel must be less than the
recording rate as described in "Recording Rate for Each
Recording Mode" above.
The following are available for image quality.
SFA/SFB: Top quality (SUPER FINE)
FQA/FQB: High quality (FINE)
NQA/NQB: Standard quality (NORMAL)
EXA/EXB: Low quality (EXTENDED)
**A is suitable for less dynamic images.
**B is suitable for more dynamic images.
The following are available for recording duration (only
event pre-recording and event post-recording).
1 s - 10 s (in 1 second intervals)
20 s/30 s/1 - 10 m (in 1 minute intervals)
20 - 60 m (in 10 minutes intervals)
MANUAL: Recording duration will be as follows depending
on the event type.
• At a motion detection: For 8 seconds
• At a video loss occurrence: During a video loss occur-
rence
• At a terminal alarm occurrence: During the supply of a
signal
• At a command alarm: For 8 seconds
CONTINUE: Recording will be performed continuously
until the [ALARM RESET] button is pressed.
w [Event Prog] Create event programs
for an event occurrence
Perform the settings of event action for each event type
(motion detection, video loss, terminal/command alarm)
or of auto copy.
● VMD
Perform the settings of event action at a motion detection or
the settings of the auto copy function.
Perform the settings for the following action mode. Refer to
page xx for further information about each action mode.
ADM (Activity Detection Mode): Performs only recording,
writing an event log and camera movement to a preset
position at an event occurrence. Other event actions
will not be performed.
ALM (Alarm Mode): Performs every event action according
to the settings.
Auto copy is the function to copy recorded images auto-
matically onto the copy area of the hard disk or the DVD-
RAM disk.
Select ON or OFF to enable or disable the auto copy func-
tion.
ON: Enable the auto copy function
OFF: Disable the auto copy function
Schedule
System
Display
Com
Switcher
SETUP MENU
LIVE
Maintenance Recording
Time Table
REC Prog
Event Prog
Special Days
Event
SETUP
SETUP
SETUP
SETUP
■
Event Program 1
■
Event Program 2
■
Event Program 3
■
Event Program 4
Schedule
System
Display
Com
Switcher
SETUP MENU
LIVE
Maintenance Recording
Time Table
REC Prog
Event Prog
Special Days
Event
SETUP
SETUP
SETUP
SETUP
■
Event Program 1
■
Event Program 2
■
Event Program 3
■
Event Action 4
Event PROG1
■
VMD
■
Video Loss
■
Terminal/Command Alarm
O K CANCEL
SETUP
SETUP
SETUP
Event Schedule
System
Display
Com
Switcher
SETUP MENU
LIVE
Maintenance Recording
Time Table
REC Prog
EVT Prog
Special Days
SETUP
SETUP
SETUP
SETUP
■
Event Program 1
■
Event Program 2
■
Event Program 3
■
Event Program 4
■
Action Mode
■
Auto Copy
VMD
OK
ALM
OFF
CANCEL