Filter
Top Products
118
2
8
3
14
7
5
6
CH01 EXT Ad P1A
[ ]
CH01 EXT Ad P1A
[ ]
CH01 ALZ
P1 W
R G B
CH01 ALZ
P1 W
R
G B
CH01 ALZ
P1 W
R
G
B
CH01 ALZ
P1
W
R
G
B
4,5,6,7
1
5
3
2
4
CH01 EXT Ad P1A
[ ]
MENU : SELECT
PUSH SPACE KEY
CH01 EXT Ad P1
[EXT D-1.50]
_
1
5
3
2
4
RANGE x,y Lv
(%) 10 10
_
MENU : SELECT
PUSH SPACE KEY
RANGE G B/G,R/G
(%) 10 10
_
RANGE R B/G,R/G
(%) 10 10
_
RANGE FMA
(%) 10
_
From the Measurement Preparation section
When performing measurement in analyzer mode
Setting Section Pages 45 to 74
To the Measurement section Page 75
When the optional 4-Probe Expansion Board CA-B15 is used
User calibration is performed independently for probe
connectors ([P1] to [P5]) for each memory channel.
1
Press the key to display the menu selection screen.
2
Press the key to open the PROBE selection screen.
3
Press the key until the desired probe no. appears.
4
Press the key to confirm the selection.
<Inputting the RGB Emission Characteristic for
Analyzer mode> Page 59
Can be set to all the memory channels.
Memory channel Probe no.
1.Press the MODE key to select analyzer mode.
2.Press the CH and keys to select the
desired memory channel.
3.Press the key.
4.Input the emission characteristic of R.
1
Place the measuring probe against the display, which is now emitting
monochrome light of R.
2 Press the key.
5.Input the emission characteristic of G.
1
Place the measuring probe against the display, which is now emitting
monochrome light of G.
2 Press the key.
6.Input the emission characteristic of B.
1
Place the measuring probe against the display, which is now emitting
monochrome light of B.
2 Press the key.
7.Input the emission characteristic of W.
1
Place the measuring probe against the display, which is now emitting
monochrome light of W.
2 Press the key.
8. Press the key.
The RGB emission characteristic for the display and
target color will be set.
●
To change the target color after user calibration:
*1
<Setting/Changing the Target Color> Page 116
●To set an ID name:
*2 <Setting an ID Name> Page 118
●To use the analog display function:
*3
<Setting the Analog Display Range> Page 118
In the LCD display section, the “ * ” mark will appear on the left of “R”.
In the LCD display section, the “ * ” mark will appear on the left of “G”.
In the LCD display section, the “ * ” mark will appear on the left of “B”.
In the LCD display section, the “ * ” mark will appear on the left of “W”.
<Setting an ID Name> Page 67
Can be set to all the memory channels.
1.Press the CH and keys to select the
desired memory channel.
2. Press the key.
3. Press the key to open the ID name input
screen.
4. Enter the desired ID name.
Number-key ( to , )Used to enter values.
Key .. Can be used to enter an alphabet,
hyphen (-) and space. Pressing this
key again will restore the original
function of the number-key.
Key .. Moves the cursor to the right each
time this key is pressed.
5. Press the key.
Memory channel
Cursor ID name
<Setting the Analog Display Range> Page 69
1.Press the MODE key to select the measurement
mode for which you want to set the range.
2. Press the key.
3. Press the key to open the RANGE setting
screen.
4. Enter the desired range value.
Ten-key ( to , )...
Used to enter values.
Key .. Moves the cursor to the right each
time this key is pressed.
5. Press the key.
*2
*3
For analyzer mode (G reference)
For analyzer mode (R reference)
For flicker mode**