Filter
Top Products
38 01-0870-401B 01/03
Using a Remote Unit
AD
x
SAMPLE RATE n/a, 0, 32, 44.1, 48 — Query-only; displays the audio sample rate. Only available
in MPEG audio mode.
AD
x
SOURCE MPEG-2, ATSC MPEG2 Query-only; displays the source for the specified audio
output.
Front panel equivalent:
Details>Audio>Slot_
x
>Audio
x
>Source
AD
x
VOL 0 - 18 dBu 18 dBu Sets the audio volume. The TDR6 cannot increase or
amplify the incoming audio level.
■ 18 dBu: output value is equal to that of the input signal
level
■ < 18 dBu: TDR6 attenuates the input signal level
Front panel equivalent:
Details>Audio>Slot_
x
>Audio
x
>Volume (analog audio only)
BISS — When BISS is entered, the decoder returns the following
information:
■ Status: <
scrambling status
>
■ Mode: <
selected BISS mode
>
■ 1Key: <************>
■ EKey: <****************>
■ EID: <**************>
BISS 1KEY <
value
>where <
value
> is a 12
character hexadecimal
value,
that does not
begin with 0x
If less than 12 characters
are entered, the TDR6
will not set the
command.
If more than 12
characters are entered,
the TDR6 truncates the
value to the first 12
characters entered.
— Sets the key value for BISS 1 mode. The 1 key value is also
referred to as the
clear session word
.
Important Considerations when entering BISS 1KEY:
■ This command must be set before BISS Mode1 is set.
■ This command may not be entered/changed more than
10 times within a five minute time period.
■ When re-entering/changing this command, there must be
at least a 10 second time delay between entries.
■ The value cannot begin with the hex values
0x
■ The value cannot be displayed once it is entered.
Instead, the TDR6 will display 12 asterisks *.
BISS EID <
value
>where <
value
> is a 14
character hexadecimal
value,
that does not
begin with 0x
If less than 14 characters
are entered, the TDR6
will not set the
command.
If more than 14
characters are entered,
the TDR6 truncates the
value to the first 14
characters entered.
— Sets the identification value for BISS E mode. The E ID
value is also referred to as the
Injected ID
.
Important Considerations when entering BISS EID:
■ This command must be set before BISS ModeE is set.
■ This command may not be entered/changed more than
10 times within a five minute time period.
■ When re-entering/changing this command, there must be
at least a 10 second time delay between entries.
■ The value cannot begin with the hex values
0x
■ The value cannot be displayed once it is entered.
Instead, the TDR6 will display 14 asterisks *.
BISS EKEY <
value
>where <
value
> is a 16
character hexadecimal
value,
that does not
begin with 0x
If less than 16 characters
are entered, the TDR6
will not set the
command.
If more than 16
characters are entered,
the TDR6 truncates the
value to the first 16
characters entered.
— Sets the key value for BISS E mode. The E key value is also
referred to as the
encrypted session word
.
Important Considerations when entering BISS EKEY:
■ This command must be set before BISS ModeE is set.
■ This command may not be entered/changed more than
10 times within a five minute time period.
■ When re-entering/changing this command, there must be
at least a 10 second time delay between entries.
■ The value cannot begin with the hex values
0x
■ The value cannot be displayed once it is entered.
Instead, the TDR6 will display 16 asterisks *.
TDR6 Remote Command Listing (continued)
Mnemonics
Parameters/
Response Values
DVB Defaults Description