Mitsubishi Electronics DX-TL5000U DVR User Manual


 
87
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
Changing playback intervals
Although, playback and reverse playback use the same
interval as that for recording, it is possible to change the
playback interval. This function is useful for slow-motion
playback of fast-moving footage, or quick playback of ex-
tensive footage without skipping frames.
step1
-1
. (To playback the picture recorded at the long
recording rate fast:)
Press the + button during playback or reverse
playback.
Playback or reverse playback is made at a speed
of 120 pps in total.
step1
-2
. (To slow down the playback speed:)
Press the button.
Each time the button is pressed, the playback
speed is changed to a slower speed (up to 0.125
pps).
step2
-1
. (To playback the recording data of the fast motion
slowly:)
Press the button during playback or reverse
playback.
Playback or reverse playback is made at a speed
of 0.125 pps per camera.
step2
-2
. (To increase the playback speed:)
Press the + button.
Each time the + button is pressed, the playback
speed is changed to a faster speed (up to 120
pps). (For the picture recorded at the pps of more
than 120, the playback speed may become slower
when you press the + button.)
Audio cannot be played back when changing the
playback interval.
Once the playback interval is changed, audio will not
be played back even when returning the playback
interval to the original value. To playback audio, stop
playback once and then playback the picture again.
Altering the playback interval to perform a quick
playback of data with long recording rate may cause
discrepancies between actual recording time and the
recording time displayed on the screen.
Simultaneous playback during recording
The recording data can be played back simultaneously dur-
ing recording.
The playback picture may pause temporarily or the
audio may be interrupted.
Noise may appear on the picture during shuttle
playback.
Split screen display can be selected individually for
recording and playback.
Playback the latest recorded contents
step1. Press the PAUSE (JUMP TO END) button when the
unit is in stop mode.
The still frame playback picture around the end
point of the latest recording is displayed.
Triplex playback
This function is used to insert the playback picture of the
desired camera number while displaying the picture
supplied from the cameras.
step1. Press the TRIPLEX PB button during split screen
display.
The unit switches to triplex playback mode.
step2. Press the desired camera number button to be
played back.
The playback picture of the selected camera
number appears.
To switch the camera number of the playback
picture, stop playback once and then follow the
steps 1 and 2 above.
step3. Press the STOP button to stop playback.
Triplex playback is available for either OUTPUT A or
B.
When the camera number button is not pressed for
more than 3 seconds after pressing the TRIPLEX PB
button, the triplex playback mode is cancelled.
The picture of the camera number which is not
displayed in the split screen display cannot be played
back. In this case, the triplex playback mode is
cancelled.
Triplex playback mode is cancelled when the button
other than camera number button is pressed.
Triplex playback mode is cancelled when the different
type of split screen is displayed. (The triplex playback
mode is not cancelled when the newly displayed split
screen contains the camera number of which picture
being played back.)
Triplex playback mode cannot be used during alarm
display function is performed. When the alarm display
is performed during triplex playback, triplex playback
is cancelled and the normal camera picture appears
when the alarm display is finished.
The blue screen appears when the data of the
selected camera number is not existed in the triplex
playback picture.
The clock which is displayed during triplex playback
indicates the time and date of the playback picture.