Filter
Top Products
Appendix A-3
Appendix
DVW-A500/1
Oxide Tape
Frequency
response (at 10 dB
below refernce
level
a)
)
50 Hz to 15 kHz
+1.0 dB/–2.0 dB
50 Hz to 15 kHz
±3.0 dB
S/N Ratio (at 3%
distortional level)
More than 72 dB
Metal TapeLNG
More than 50 dB
(Dolby NR off)
Distortion (T.H.D at
1 kHz reference
level
a)
)
Less than 1% Less than 2%
Wow and flutter Less than 0.1% rms
AFM
Frequency
response (at
reference level
a)
)
20 Hz to 20 kHz +0.5 dB/–2.0 dB
S/N Ratio (at 3%
distortional level)
More than 85 dB
Distortion (T.H.D at
1 kHz reference
level
a)
)
Less than 0.5%
DVW-A500P
Oxide Tape
Frequency
response (at 20dB
below peak level
a)
)
50 Hz to 15 kHz
+1.0 dB/–2.0 dB
50 Hz to 15 kHz
±3.0 dB
S/N Ratio (CCIR
468-3 weighted, at
3% distortional
level)
More than 68 dB
Metal TapeLNG
More than 62 dB
a) Reference level: + 4 dBm
Audio
Processor adjustment range
Video level ±3 dB/–∞ to +3 dB selectable
Chroma level ±3 dB/–∞ to +3 dB selectable
Setup/Black level ±30 IRE/±210 mV
Y/C delay ±100 ns (in Betacam playback on
DVW-A500/1 and A500P/1)
Chroma phase ±30°
System phase Sync: ±15 µs
SC: ±200 ns
Input connectors
SERIAL V/A INPUT
BNC (1 with active through out)
Serial digital (270 Mbits/s)
SMPTE 259M/CCIR 656-III
ANALOG I/O VIDEO INPUT
REF.VIDEO: BNC (2 in loop through
connection)
Black burst or composite sync
0.3 Vp-p, 75 Ω, Sync negative
COMPONENT:BNC (3 for 1 set)
Y: 1.0 Vp-p, 75 Ω, Sync negative
R-Y/B-Y: 0.7 Vp-p, 75 Ω, with
100% color bar for DVW-
A500P/1 and 500P/1 and with
100% or 75% color bar
selectable for
DVW-A500/1 and 500/1
COMPOSITE: BNC (2 in loop through
connection) 1.0 Vp-p, 75 Ω, Sync
negative (with optional BKDW-
505/506)
AUDIO INPUT (AES/EBU) CH-1/2, CH-3/4
XLR, 3-pin, female (2)
AES/EBU format, balanced
AUDIO INPUT CH-1/2/3/4/CUE
XLR, 3-pin, female (5)
LOW OFF: –60 dBu, high
impedance, balanced
HIGH OFF: +4 dBu, high
impedance, balanced
HIGH ON: +4 dBm,600 Ω
termination, balanced
TIME CODE IN XLR, 3-pin, female (1)
0.5 to 18 Vp-p, 10 kΩ, balanced
Distortion (T.H.D at
1 kHz reference
level
a)
)
Less than 1% Less than 2%
Wow and flutter
(DIN 45507
weighted)
Less than 0.1%
AFM
Frequency
response (at
reference level
a)
)
20 Hz to 20 kHz +0.5 dB/–2.0 dB
S/N Ratio (at 3%
distortional level)
Distortion (T.H.D at
1kHz reference
level
a)
)
Less than 0.5%
a) Reference level: +4 dBm
b) Peak level: +8 dB above reference level
Unless otherwise specified, all values in the above table
were obtained by measuring analog output signals with
Dolby noise reduction circuitry on.
More than 72 dB (CCIR 468-3
weighted)