Filter
Top Products
12
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
By pressing the camera number buttons, you can
view the picture from the camera even it is not set
to be recorded.
2. SPLIT/SEQUENCE button
By pressing this button you can switch the display mode
from SPLIT 9 which has been set on the <SPLIT SCREEN
SETTING> menu, SPLIT 4 ( type a, b, or c), Single-screen
sequential and 4 screens sequential.
3. ZOOM button
When this button is pressed, the ZOOM POINTER (X) ap-
pears on the screen.
By pressing this button, Camera
number buttons 4 to 9 change its function as follows:
4. ZOOM IN button (Camera numbner button 4)
Press this button after pressing ZOOM button, the displayed
picture will be enlarged by 2 steps: twice as large and 4
times as large as the original picture size. The enlarging
ratio will be displayed on the top left-hand corner of the
screen.
5. ZOOM OUT button (Camera numbner button 5)
Press this button anytime after operating ZOOM button and
ZOOM IN button, the picture size will be reduced in 2 steps
from the enlarged picture. The enlagement ratio will be
displayed on the top left-hand corner of the screen.
6. MOVE buttons (Camera numbner buttons 6 to 9)
By pressing these buttons you can move the ZOOM
POINTER (X). The picture will be enlarged/reduced from
this pointer in the centre. After enlarging reducing the size
of the picture, you can also move the whole picture by
pressing these buttons. For more details please refer to
“Multiplexer buttons” on page 36.
■ Basic recordings
The correct settings are necessary for your recordings. For
details of each setting, please refer to the following pages
of this instruction manual:
The <HDD FULL> menu setting: sets the move-
ment of the unit when it runs out of the recording
capacity of HDD during recording. Please refer to
page 30, “HDD repeat recording” setting.
The <CAMERA SETTING> menu setting: sets
the cameras to be operated from all connected cam-
eras for each camera usage. Please refer to page
38, “Camera usage setting”.
The <CAMERA USAGE> menu setting: chooses
and sets the camera usage from A, B or C on the
<CAMERA SETTING> menu. Please refer to page
38, “Camera usage setting”.
After confirming all settings of recording, please proceed
as written on the right.
Basic Operations (continued)
♦ Storage space indicator function
This unit is capable of constantly displaying the amount of
data recorded in the recording device designated on-screen
(i.e., the main unit or an archive device
Glossary
).
Also, when the designated remaining amount has been
reached, the amount used (%) display will begin flashing.
In the case of the HDD, the percent displayed is the per-
centage relative to the entire HDD storage capacity as rec-
ognized in the MAIN HDD setting. In the case of the backup
device, the percentage is relative to the storage capacity
of the medium. The following settings are necessary to bring
these functions into effect.
1) On the <REAR TERMINAL> menu, use CAPAC-
ITY REMAIN to select the device and set the re-
maining capacity (refer to page 26).
2) On the <TIME DATE DISPLAY> menu, set the
DISPLAY MODE to “3” (refer to page 24).
3) Select one screen using the multiplexer buttons.
When using the multiple screen display, set the CH.
TITLE parameter on the <MPX FUNCTIONS> menu
to NONE (refer to page 39).
■ Multiplexer functions
You can use a part of multiplexer functions by using the
multiplexer buttons placed on front of the unit.
♦ Multiplexer buttons
231 4 65 98721
3. ZOOM button
2. SPLIT/SEQUENCE button
4. ZOOM IN button
5. ZOOM OUT button
6. MOVE buttons
1.Camera number buttons (1 to 9)
ZOOM
SPLIT/SEQUENCE
0
You cannot operate the multiplexer buttons when
the menu is displayed on screen. The multiplexer
functions does not work when the unit is accessing
the peripheral recording device or ARCHIVE but-
ton, COPY button or PLAY button is flashing.
1. Camera number buttons
By pressing these buttons, the images from cameras con-
nected to CAMERA IN terminals at the rear of the unit will
be displayed on screen. If the images of the camera that is
not set to be operated is selected on the <CAMERA SET-
TING> menu , the Non-operattion camera mark will be dis-
played on screen.
09-06-2000 FRI
00:00:00 25F
Non-operation camera mark