Filter
Top Products
47
ENGLISH
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Operations
♦ Operation when the hard disk drive becomes full
“REC•STANDBY”(Recording standby): The unit stops re-
cording at the moment its hard disk becomes full. The unit
will begin recording by over-writing its hard disk when the
unit receives an alarm signal or a REC terminal signal, or
when the REC button is pushed.
“ALARM•PROT”(Alarm protection): If there is even one in-
stance of Alarm Recording to finish setting, the unit will
stop recording the moment its hard disk becomes full and
will display the HDD FULL message on the monitor. When
WRNG is entered as the BUZZER value (found in the
<REAR TERMINAL> menu), the buzzer will also be acti-
vated. When the CALL OUT value (found in the <REAR
TERMINAL> menu) is ON, a CALL OUT signal will be emit-
ted from the CALL OUT terminal. If there are no instances
of Alarm Recording during recording, the unit will continue
recording by automatically over-writing its hard disk.
“STOP”: The unit will stop recording at the moment the
hard disk becomes full, and will display the HDD FULL mes-
sage on the monitor. When WRNG is entered as the
BUZZER value (found in the <REAR TERMINAL> menu),
the buzzer will also be activated. The unit will stop record-
ing when there is no more storage space in memory. When
the CALL OUT value (found in the <REAR TERMINAL>
menu) is ON, a CALL OUT signal will be emitted from the
CALL OUT terminal. To restart over-writing on the hard disk,
first press the WARNING RESET button to cancel HDD
FULL, and then press the REC button.
■ Series Recording
By connecting multiple units as show in the chart below
and selecting REC•STANDBY in the HDD Repeat Record-
ing setting, this unit can perform Series Recording. In Se-
ries Recording, when the first unit’s hard disk has become
full, the second unit automatically begins recording.
System configuration (using two units)
REC
ALARM-OUT
POWER OFF
POWER ON
MODE-OUT
CALL OUT GND
CALL OUT
DC 5V OUT
MAX 30mA
CLOCK ADJUST
REC
POWER ON
POWER OFF
ALARM OUT
MODE OUT
CALL OUT
CALL OUT GND
First Unit
Second Unit
GND
GND
GND
GND
GND
1
INFORMATION
In this example, when the first unit’s
hard disk reaches its maximum storage capacity, the
second unit will begin recording; when the second
unit’s hard disk reaches its maximum storage ca-
pacity, the first unit will begin recording by over-writ-
ing its hard disk. If you do not want the first unit to
begin the over-writing process, then configure the
system as illustrated in the graph (see 1 above).
The Series Recording function can also be put into
effect by connecting the CALL OUT terminal in place
of the MODE OUT terminal, and the disk storage
capacity setting is made in the <CALL OUT> menu.
When the CALL OUT terminal is used, if the first
unit experiences malfunction or cannot otherwise
continue recording, the second unit will initiate its
recording process.
♦ Setting the Series Recording (for both units)
1. Press the SET UP button to display the <MENU SETTING>
menu.
2. Turn the JOG dial to move the cursor to the REAR TERMINAL
then turn the SHUTTLE ring to the right.
<REAR TERMINAL>
@MODE OUT
CAPACITY REMAIN
REC
HDD-10%
3. Turn the JOG dial to move the cursor to CAPACITY REMAIN
then turn the SHUTTLE ring to the right.
• The sub-item will start flashing.
<REAR TERMINAL>
MODE OUT
@CAPACITY REMAIN
REC
HDD-10%
4. Check that the “HDD” is flashing. Turn the SHUTTLE ring to
the right.
• Choose the HDD so that the second unit begins recording
when the first unit’s hard disk approaches its storage limit.
• The flashing will move to capacity setting.
<REAR TERMINAL>
MODE OUT
@CAPACITY REMAIN
REC
HDD-10%
5. Turn the JOG dial till desired capacity remain appears and
then turn the SHUTTLE ring to the right.
• The sub-item will stop flashing.
<REAR TERMINAL>
MODE OUT
@CAPACITY REMAIN
REC
HDD-10%
6. Turn the JOG dial to move the cursor to MODE OUT and
turn the SHUTTLE ring to the right.
• The sub-item will start flashing.
<REAR TERMINAL>
@MODE OUT
CAPACITY REMAIN
REC
HDD-10%
7. Turn the JOG dial to flash “REMAIN”and turn the SHUTTLE
ring to the right.
• The sub-item will stop flashing.
<REAR TERMINAL>
@MODE OUT
CAPACITY REMAIN
REMAIN
HDD-10%
8. Display the <INITIAL SET UP> menu.
• Press the SET UP button to display the <MENU SETTING>
menu. Move the cursor to INITIAL SET UP and turn the
SHUTTLE ring to the right.
<INITIAL SET UP>
@TIME DATE ADJUST
ARCHIVE OVERWRITE
HDD FULL
HDD PB REPEAT
AUTO EJECT
ARCHIVE DATA
OFF
STOP
STOP
ON
ALL
9. Turn the JOG dial to move the cursor to HDD FULL and
turn the SHUTTLE ring to the right.
• The sub-item will start flashing.
<INITIAL SET UP>
TIME DATE ADJUST
ARCHIVE OVERWRITE
@HDD FULL
HDD PB REPEAT
AUTO EJECT
ARCHIVE DATA
OFF
STOP
STOP
ON
ALL