Filter
Top Products
13
ENGLISH
•
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Basic Operations
2. Turn the SHUTTLE ring to the right to flash the sub-item.
<RECORDING SET UP>
REC INTERVAL
@REC P.GRADE
AUDIO RECORDING
<ESTD TIME>
12.5F
HIGH
OFF
18H23M
3. Turn the JOG dial to display STANDARD then turn the
SHUTTLE ring to the right.
• The “STANDARD” is now selected.
<RECORDING SET UP>
REC INTERVAL
@REC P.GRADE
AUDIO RECORDING
<ESTD TIME>
12.5F
STANDARD
OFF
27H16M
By turning the JOG dial, the recording picture
grade setting will be changed as below:
HIGH SUPERIOR LOW
STANDARD BASIC
4. Check the estimated recording time.
• After setting the recording interval, the <ESTD TIME> will
be displayed. By changing recording settings, <ESTD TIME>
will change its length of time (Alarm recording setting is not
concerned with this).
<RECORDING SET UP>
REC INTERVAL
@REC P.GRADE
AUDIO RECORDING
<ESTD TIME>
12.5F
STANDARD
OFF
27H16M
The available recording time will be changed de-
pending on the setting of the recording interval and
the recording picture grade. This estimated record-
ing time display will include the additional HDD which
has been built to the Unit. The estimated time may
not show the exact time if the recording interval was
set to long. For available recording time, please re-
fer to “Recording time table” on pages 71 and 72.
5. Press the SET UP button to go back to the present time
display.
• Press the camera number button and confirm if there is a
picture input to the CH you have selected to be recorded.
6. Press the REC button.
• The REC button starts illuminating and the recording starts.
• If you press the PAUSE button during recording, recording
will be in pause mode. To release it, press the pause button
again (this PAUSE button only works when built-in HDD is
selected as a playback device).
Please refer to “Choosing among the devices”
on page 51 for selecting a playback device.
7. Press the STOP button to stop recording.
• The REC button will stop illuminating.
This recording time lists recording times for
when the capacity of the built-in HDD is 30.0 GB.
Please note that alterations to the built-in HDD
may contribute to slightly longer recording times
than those listed on this recording time.
♦ Setting the recording interval
Example: Setting the recording interval to “12.5F” (the de-
fault setting is “25F”).
1. Turn the unit on after turning the peripheral recording device
on.
If the <DEVICE CHECK> menu appears at this
stage, the setting of the peripheral recording de-
vice may have been changed. For details please
refer to “When to install the extra hard disk drive or
change the ID number” on page 19.
2. Press the SET UP button to display the <MENU SETTING>
menu.
3. Turn the JOG dial to move the cursor ( ) to RECORDING
SET UP then turn the SHUTTLE ring to the right.
• The <RECORDING SET UP> menu appears.
<RECORDING SET UP>
@REC INTERVAL
REC P.GRADE
AUDIO RECORDING
<ESTD TIME>
25F
HIGH
OFF
9H11M
4. Check that the cursor is next to the REC INTERVAL and
turn the SHUTTLE ring to the right.
• The sub-item of REC INTERVAL will start flashing.
<RECORDING SET UP>
@REC INTERVAL
REC P.GRADE
AUDIO RECORDING
<ESTD TIME>
25F
HIGH
OFF
9H11M
The setting you are making here is only for the
normal recording, NOT for the timer recording and
the alarm recording. You need to make the timer re-
cording settings and the alarm recording settings on
the <TIMER PROGRAM> menu. For details please
refer to “Various recording settings” on page 33.
5. Display 12.5F by turning the JOG dial then turn the
SHUTTLE ring to the right.
• The flashing will stop. Now the setting has been completed.
<RECORDING SET UP>
@REC INTERVAL
REC P.GRADE
AUDIO RECORDING
<ESTD TIME>
12.5F
HIGH
OFF
18H23M
By turning the JOG dial, the set-
ting will be changed as below:
25F 12.5F 8.33F 6.25F 4.17F 2.78F
SHOT 0.13F 0.25F 0.5F 1F 1.56F 2.08F
♦ Changing the recording picture grade
Example: Setting the recording picture grade to “STAND-
ARD” (the default setting is “HIGH”).
1. After step 5 of REC INTERVAL setting procedures above,
turn the JOG dial and move the cursor to “REC P. GRADE”.
<RECORDING SET UP>
REC INTERVAL
@REC P.GRADE
AUDIO RECORDING
<ESTD TIME>
12.5F
HIGH
OFF
18H23M