Filter
Top Products
50
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
■
Time date search
Please refer to page 14 for detailed operation.
■ Index Search
During Alarm Recording, an index signal will automatically
be written onto the hard disk. Index Search is a process of
retrieving still frames using their associated index signal.
The index count can be set, as desired, up to 99.
Example: Enter 10 for the index count, then start a search.
1. Press the SEARCH button to display the <SEARCH
SELECTION> menu.
2. Turn the JOG dial to move the cursor to INDEX SEARCH
and turn the SHUTTLE ring to the right.
• The <INDEX SEARCH> menu will appear.
<SEARCH SELECTION>
TIME DATE SEARCH
@INDEX SEARCH
SKIP SEARCH
ALARM LIST SEARCH
JUMP TO START POINT
3. Turn the JOG dial to display the desired index count, then
turn the SHUTTLE ring to the desired search direction. (Turn
right to move forward, turn left to move in reverse.)
When using DDS tape, index searches can be
performed in the
forward direction only.
• Index Search will begin, and images of the desired index
count will appear on SPLIT 9 screen as still frames.
• The index count will begin blinking if the index signal has not
been recorded, i.e., the Index Search will not be executed. Press
the SEARCH button when the unit returns to normal playback mode.
<INDEX SEARCH>
10
I n p u t INDEX DATA.
T u r n t h e SHUTTLE RING
<< or >> t o SEARCH.
4. To change the search image from SPLIT 9 screen to the
single screen, select the camera number by pressing the
CAMERA NUMBER button on the front of this unit.
• First press the SEARCH button, then delete the <SEARCH
SELECTION> menu.
• The selected image will be shown on the Single screen mode.
Cannot change the display, during the search
selection menu will appear.
5. To play back search results.
• Press either the PLAY button or the PAUSE button.
Refer to page 49 for details on Various playback.
To exit the <INDEX SEARCH> menu without ac-
tivating the search, press the SEARCH button on
the front of the unit.
6. Press the STOP button to stop playback and still frame mode.
• Press the SEARCH button, the display will revert to its
original state.
♦ How to count index signals
Present time in the diagram below represents the point of
playing back or stopped playing back. To search index
with “+”, turn the SHUTTLE ring to the right to search for-
ward. To search index with “-”, turn the SHUTTLE ring to
the left to search backward.
Various search
Present position
Beginning of playback device
End of playback device
-15 -1-2 +1 +15+2
A•REC A•REC A•REC A•REC A•REC A•REC
A•REC: Alarm Recording
■ Skip Search
Skip Search is a process where the unit automatically
searches for an index signal, then retrieves the visuals
associated with that index and plays back the images for 5
seconds each.
To play back search results, press the PLAY but-
ton for the desired image.
1. Press the SEARCH button to display the <SEARCH
SELECTION> menu.
2. Turn the JOG dial to move the cursor to SKIP SEARCH
then turn the SHUTTLE ring to the right.
• The <SKIP SEARCH> menu will appear.
<SKIP SEARCH>
Turn the SHUTTLE RING
<< or >> to SEARCH.
3. Turn the SHUTTLE ring to desired direction (Forward search
to the right and reverse to the left).
• The unit begins the Index Search, and plays back the images
associated to the index for five seconds each on SPLIT 9 screen.
Depending on the recording condition of the in-
dex signal, there might be occasions when Skip
Search cannot be performed.
The unit cannot be selected to single screen dis-
play mode during Skip Search.
4. Press the STOP button to stop searching.
■ Alarm List Search
When Alarm Recording is initiated (refer to page 45), the
Alarm Recording start time will be added to the Alarm List.
Alarm List Search is a process which uses the associated
Alarm Recording start time to retrieve a desired image for
still frame playback.
Alarm Recording start-times can be registered
up to 500 times. After the 500th time, the first start-
time will be erased and the 501st start-time will be
added to the list.
1. Press the SEARCH button to display the <SEARCH
SELECTION> menu.
2. Turn the JOG dial to move the cursor to ALARM LIST
SEARCH then turn the SHUTTLE ring to the right to display
the <ALARM LIST SEARCH> menu.
<SEARCH SELECTION>
TIME DATE SEARCH
INDEX SEARCH
SKIP SEARCH
@ALARM LIST SEARCH
JUMP TO START POINT
3. Turn the JOG dial till the cursor goes to desired alarm list
number, then turn the SHUTTLE ring to the right.
• The unit begins the ALARM LIST SEARCH, and retrieves the
image associated with the selected time (or the time closest to
the selected time) for still frame playback on SPLIT 9 screen.