Mitsubishi Electronics WD-57831 CRT Television User Manual


  Open as PDF
of 126
 
40 Chapter 3. TV Setup
When You First Connect a Device
,
continued
1. ConnectthedevicetotheTVwith an IEEE 1394
cable first.
2. WhentheNew1394Devicescreenappearswiththe
Analog Connectioncheckboxhighlighted,press
ENTER
toenteracheckmark.Seefigure7,New1394
Devicescreen.
3. IntheNew1394Devicescreen,notethename
assignedtothedevice,asyouwillneedtousethe
samenameinalaterstep.Seefigure7.
4. ConnectthedevicetotheTVwiththesupplemental
analogcables.
5. ThenextscreenistheAutoInputSensingscreen
(seefigure6)inwhichyoucanselectanameforthe
device.SelectthesamenameyounotedintheNew
1394Devicescreen(seefigure7).
• Ifyouselectthewrongnameforthedevice,you
willbeunabletoswitchbetweentheanalogand
digitalinputstotheTV.
• IfyouconnectanIEEE1394cableboxandit
isdetectedasCABLEintheNew1394Device
screen,besuretoselectthenameCABLE asthe
namefortheanaloginputand notcablebox.
Note: Ifyouconnectedthecablesinreversesequence
(analogrst),youwilllaterneedtochangethe
inputnameintheInputNamemenu.
a. Switchtoanyviewingdeviceotherthanthe
oneyouwishtochange(press
INPUT
toopen
theInputSelectionmenu,highlighttheinput
icon,andpress
ENTER
).
b. OpentheNetCommandmenuandthenopen
theInputNamemenu.
c. Highlightthetextboxfortheanaloginput
usedfortheIEEE1394device.
d. Press toscrollthroughtheavailable
namestodisplaythenameyouearliernoted
fortheIEEE1394device.
e. Press
EXIT
.
Initial NetCommand® Setup
What You Need to Know About NetCommand
• NetCommandsetupisoptional.
• NetCommandoperatesbysendingsignalsfromthe
TVtoyourotherdevicesviatheIRemitters,tellingthe
devicestoplay,record,changeinputs,adjustvolume,
changechannelsandmanymorefunctions.Allthis
isaccomplishedwiththeTV’sremotecontrolandthe
slideswitchleftinthe
TV
position.
• TheIR“Learning”featureofNetCommandallowsthe
TVtolearntheremotecontrolsignalsforyourA/V
devices.
• NetCommand®cancontrolIEEE1394devicesby
sendingcontrolsignalsoveraFireWire®cable.
• YoucanchoosethelevelofNetCommandcontrolfor
yourhometheater.
Limited Setup. Performalimitedsetupifyou:
WantNetCommandtocontrolonlyafew
devices,suchastheTV,aplaybackdevice
(likeaDVDplayer),andacablebox.Withthis
setup,youcanusetheTV’sremotecontrolto
operatethesedevices.
WanttouseTVGuideOnScreen®tocontrol
yourcableboxandVCRand/orA/Vdisc.
Afterperformingthissetup,youcanusethe
TV’sremotecontroltooperatethesedevices.
WanttheeaseandflexibilityofNetCommand-
controlledrecording,withseamlesssetupof
time-delayedorimmediaterecordingsamong
networkeddevices.
Full Setup. Performafullsetupifyouwantto
giveNetCommandthefollowingadditionalcontrol:
ControlasurroundsoundA/Vreceiver.
Automaticallychangeinputselectionsforthe
A/Vreceiver.
Initial NetCommand Setup for Most Device
Types
• TosetupanA/Vreceiver,see“AdditionalSetupUsing
theNetCommandMenu”laterinthischapter.
• Forsetuplater,ortomakechangestothesetup,see
“AdditionalSetupUsingtheNetCommandMenu”later
inthischapter.
1. ConnectandpositiontheIRemittersasdescribedin
chapter2,“TVConnections.”
2. HavetheremotecontrolsfortheTVandtheother
devicereadybeforebeginning.SettheTVremote
control’sslideswitchtothe
TV
position.
3. IntheAutoInputsensingscreen(seefigure8),high-
lighttheLearnbuttonandpress
ENTER
toopenthe
Learnscreenforthedevice(seefigure9).
 previous next