Mitsubishi Electronics WD-57831 CRT Television User Manual


  Open as PDF
of 126
 
Chapter 3. TV Setup 43
Initial NetCommand® Setup,
continued
Review TV Connections
YoucanverifyTVconnectionsduringTVsetuporat
anytimeafterwardusingtheReviewscreen.Inthe
NetCommandmenu,press tohighlightReview
andpress
ENTER
t
odisplaytheReviewscreen(seefigure11).
Figure 11. The Review screen lists all TV connections.
IEEE 1394 devices are listed separately on the right.
Set Up TV Guide On Screen®
SetupoftheTVGuideOnScreensystemisoptional.
• ManyfeaturesofTVGuideOnScreenareavail-
ablewithoutNetCommandcontrol.Forexample,
programlistings,programsearches,andprogram
remindersfunctionwithoutNetCommand.
•
Forfullfunctionality,youmustsetupNetCommand
controlofanydeviceassociatedwithTVGuideOn
Screen,e.g.,arecordingdeviceifyouwishtoset
uprecordingsthroughTVGuideOnScreen.
1. HighlighttheGuidebuttonintheNetCommandmenu
andpress
ENTER
todisplayTVGuideOnScreensetup
options.
2. ToenabletheTVGuideOnScreensystem,highlight
theOnbutton.Ifyouwishtodisablethesystem,high-
lighttheOffbutton.
Figure 12. TV Guide On Screen setup
3. Selectprogramsourcesforthelistings.Youcan
selectoneover-the-airsourceandonecablesource
forTVGuideOnScreen.If,however,youhavemul-
tiplecablesources,thechannel-numberassignments
maynotmatchupcorrectly.Seethefollowingtable
andnotesforthepreferredconnectioncombinations.
If One Source Is:
The Other Source Can Be:
Ant-1 Air Ant-2 Air
CableBox
CableCard N/A
Ant-1ChannelsviaCable N/A
Ant-2ChannelsviaCable N/A
Note:
• InputstoTVGuideOnScreencanincludeonlyone
over-the-airsourceandonlyonecablesource.
• TVGuideOnScreenlistingscanbedownloadedfrom:
Anover-the-airantennaordirectcableconnected
toANT 1orANT 2.
AcableboxconnectedtoVIDEOorS-VIDEOon
INPUT 1, 2,or3.
AcableboxconnectedtoCOMPONENT 1, 2,or
3whenanalogchannelsaresenttotheTVas480i
signals.
• ListingscannotbedownloadedtotheTVfrom:
AcableboxconnectedtoCOMPONENT 1, 2,or
3whenallchannelsaresenttotheTVas480p,
720p,or1080isignals.
AcableboxconnectedtoHDMI 1orHDMI 2.
AcableboxconnectedtotheTVonlyviaIEEE
1394cable.
• Ifyourcableboxisconnectedusingoneoftheincom-
patibleconnectionsnotedabove,connectanover-
the-airantenna.TheTVwilldownloadTVGuideOn
Screenlistingsforboththecableboxandtheantenna
fromtheantennaconnection.
4. MovetotheZIP Codeboxandenterthefive-digitZIP
codeforyourlocation.Toreceivethecorrectprogram
listingsforyourarea,youmustentertheZIPcode.
Add or Remove Device Keys from
NetCommand Control
1. To“Learn”devicekeys,youmustbewatchingthe
device.Press
INPUT
,highlighttheiconfortheaffected
device,andpress
ENTER
.
2. OpentheNetCommandmenu,highlighttheLearn
button,andpress
ENTER
.
3. WhentheLearnscreendisplays
• Toaddkeys:Continueasdescribedearlierunder
“InitialNetCommandSetupforMostDevice
Types.”
• Todeletekeys:Highlightthenameofthekeyyou
wishtodeleteandpress
CANCEL
ontheTVremote
control.Thisclearsthecheckmarktoindicatethat
thekeyhasbeenremoved.
 previous next