Filter
Top Products
62
RS-232C
O
Query control commands
Data transmitted by PC Data returned from unit in response Description of command
[STX] QLH [ETX] [STX] LHRhhhh [ETX] Queries the current value of the hour meter.
[STX] QLM [ETX] [STX] LRMm [ETX] Queries the timer recording mode setting.
[STX] QLP:n [ETX] [STX] LPLnn:data1:data2 [ETX] Queries the POWER LOSS MEMORY data.
[STX] QLT [ETX] [STX] LTMm [ETX] Queries the setting of the recording/playback time mode.
[STX] QMA [ETX] [STX] LMAm [ETX] Queries the search mode.
[STX] QMP [ETX] [STX] LMPp:c
0
c
1
c
2
c
3
[ETX]
Queries the settings for switching the screen display (4-in-1
or 1-screen display) and for the camera numbers.
[STX] QNL [ETX] [STX] LLLm [ETX]
Queries the synchronization system setting for the cameras
to be connected.
[STX] QNR [ETX] [STX] VNRm [ETX]
Queries the setting of the video signals which are to be
output to the monitor screen in all modes except for the
recording mode.
[STX] QLZ [ETX] [STX] LBZm [ETX]
Queries the setting of the buzzer operation during alarm
recording or sensor recording.
[STX] QIP:n [ETX] [STX] LIPn:data1:data2:t [ETX] Queries the internal timer recording setting.
[STX] QIR [ETX] [STX] LUImdata [ETX] Queries the user ID of the playback tape.
[STX] QIW [ETX] [STX] LIWabcdefgh:ijklmnop [ETX] Queries the settings of the weekly timer and daily timer.
[STX] QLA:m [ETX] [STX] LAmn [ETX]
Queries the setting for the operation mode that is to be
established when an alarm signal has been input at the
tape-end position and for the duration of the alarm
recording and/or sensor recording.
[STX] QMS [ETX] [STX] LMSm [ETX]
Queries the setting of the timing at which the video signals
which are supplied from the camera and which are to be
output from the rear panel VIDEO OUT connector are to be
switched.
[STX] QLD:n [ETX] [STX] LANnn:data1:data2 [ETX] Queries the ALARM RECALL data.
[STX] QLE [ETX] [STX] LRIm [ETX]
Queries the setting for alarm recording or sensor recording
if an alarm signal has been input while repeat recording is
underway or while the tape is being rewound.
[STX] QOP [ETX] [STX] data [ETX] Queries the unit’s operation mode.
[STX] QOR [ETX] [STX] ORm [ETX] Queries the results yielded by performing REC REVIEW.
[STX] QOS [ETX] [STX] OPSdata [ETX] Queries the operation modes.
[STX] QPB:m [ETX] [STX] LPBm:r:data [ETX] Queries playback tape information.
[STX] QRA [ETX] [STX] RAm [ETX] Queries the ACK (acknowledge) code response setting.
[STX] QRE [ETX] [STX] LRBm [ETX]
Queries the setting of the buzzer operation in the event that
the unit is kept in the stop mode for a prolonged period of
time.
[STX] QRF [ETX] [STX] LNRf:p:t [ETX]
Queries the settings of the recording mode, picture quality
and recording type.