Filter
Top Products
57
Function menus (continued)
<DIAG>
This enables confirmation of information such as the
warning/hour-meter/UMID.
Verification, deletion of the error log file, retention/call to the
SD memory card can do with the SHIFT picture.
Warning display
When a warning occurs in this VTR, the warning mark (W)
blinks at the top left of the screen. If (WARN) is now
pressed, the details of the warning can be checked out on
the LCD monitor.
When more than one warning has occurred, turn the ADJ
dial to scroll through the messages.
Hour-meter display
When (HOURS) is pressed, the hour-meter information
can be checked out on the LCD monitor.
UMID display
Press (UMID) to confirm the current UMID information
for the image on the LCD monitor.
DIF Status display
Press (DIF1) or (DIF2) to display the different kinds
of information about the current DIF (IEEE 1394 interface).
Error log function
The error log mode can be selected by pressing the
button and switching the screen to <DIAG SHIFT>.
General description
When the following warnings have occurred while the tape is
running, the warning messages, time codes and operating
modes are saved, and a list of this information can be read
out on the LCD monitor. Up to 99 warnings which have
occurred can be saved. If the storage capacity of 99
warnings is exceeded, the processing that is conducted as a
result is based on the setup menu item No.015 (AUTO
STEP) setting.
LCD monitor displays
Operation mode display
This indicates the operation mode at the point when the
warning was saved.
Warning display
This indicates the warning message which is saved.
Saved warning status display
This indicates the number of the currently displayed warning
which has been saved and the total number of warnings
which have been saved.
Time code display
This indicates the time code at the point when the warning
was saved.
Cueing up the tape to the warning point
The warning list displayed on the LCD monitor can be
scrolled by turning the ADJ dial. When the warning
occurrence point to be checked is selected and the
PREROLL button is pressed, the tape is cued up to the
position of the time code which has been saved.
F1
SHIFT
F2 F3 F4 F5 F6
Warning mark
F1
F2
F2
DIAG-MENU UMID INFO
MATNO
COPY
OWNR
JPN :ORG :USER
JAN-28-02
23:30:30 +03h00m
±3775m 3D
E 180'00'00.0'
N 90'00'00.0'
POS
DATE
TIME
00001234005678BA
00B0458201000001
0
F4
F5
DIAG-MENU DIF STATUS 1
NODE CNT
MY ID
ROOT ID
IRM ID
RCV ID
GAP CNT
EUI-64
1
0
0
0
0
63
0080458200000000
DIAG-MENU DIF STATUS 2
<INPUT> <OUTPUT>
FMT
RATE
N/P
CHN 63
SPEED
STAT STOP
VIDEO
AUDIO
FMT
RATE
N/P
CHN
SPEED
START
VIDEO
AUDIO
HD100
1X
NTSC
63
400
OK
OK
OK
SHIFT
F1
SHIFT
F2 F3 F4 F5 F6
Warning messages
which are saved
Description
(Refer to page 129 and following.)
NO RF A blank section on the tape lasting more than
1 second has been detected. (During normal
playback)
SV NOT LOCKED The servo has been disengaged for more
than 3 seconds. (During recording, normal
playback or editing)
LOW RF An envelope level which is about 1/3 of nor-
mal or a CTL level which is about 1/6 of nor-
mal has been detected for more than 1
second. (During recording, normal playback
or editing)
HIGH ERROR RATE The error rate has deteriorated, and correc-
tion or compensation has been applied to the
video or audio playback signals. (During nor-
mal playback)
Operation mode display
Time code
display
Warning display
Saved warning status display