Filter
Top Products
95
Setup menus (continued)
<TIME CODE> (continued)
SBC (sub code data) area:
This is an area on the helical track, and it is separate from the video
and audio data area. The time codes, recording dates and times
and other tape control information complying with SMPTE/EBU
standards are stored here. As with the conventional LTC (linear
time code), the time code can be read even during rewinding or fast
forwarding. It can also be read out when the tape has stopped.
VAUX (video auxiliary data) area:
This area is to be found in the video data area on the helical track.
The additional information relating to the video data is stored here.
*1 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or 50 Hz
(HD, SD) mode is selected in System Menu No. 25 (SYSTEM
FREQ), this item is not displayed.
*2 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, 50 Hz (HD,
SD) mode or 50 Hz mode is selected in System Menu No. 25
(SYSTEM FREQ), this item is not displayed.
The underlining (__) denotes the factory setting mode.
No./Item Description of setting
508*
1
BINARY GP
For setting how the user bits of the time code
generated by the TCG is to be used.
0000 000
NOT SPECIFIED (no character set specified)
0001 001
ISO CHARACTER (8-bit character set complying
with ISO646, ISO2022 standards)
0002 010
UNASSIGNED 1(undefined)
0003 011
UNASSIGNED 2(undefined)
0004 100
UNASSIGNED 3(undefined)
0005 101
PAGE/LINE
0006 110
UNASSIGNED 4(undefined)
0007 111
UNASSIGNED 5(undefined)
509
PHASE CORR
For selecting whether to exercise phase
correction control over the LTC which is
generated by the TCG.
0000 OFF
Phase correction control is not exercised.
0001 ON
Phase correction control is exercised.
510*
1
TCG CF FLAG
For selecting whether to set the CF flag of the
TCG to ON or OFF.
0000 OFF
The CF flag is set to OFF.
0001 ON
The CF flag is set to ON
511*
2
DF MODE
For selecting the drop frame or non-drop frame
mode for CTL and TCG.
0000 DF
The drop frame mode is selected.
0001 NDF
The non-drop frame mode is selected.
<Note>
This DF mode setting takes effect only when
LOCAL is selected or when “ENA” has been
selected as the setup menu item No.001 (LOCAL
ENA) setting.
512*
1
TC OUT REF
For switching the phase of the time code, which
is output from the TIME CODE OUT connector,
in response to the external LTC input when a
setting other than “INT” has been selected for
setup menu item No.507 (TC SOURCE). (In EE
mode only)
0000 VOUT
The phase is aligned with the output image.
0001 TC IN
The phase is aligned with the external time code
input.
No./Item Description of setting
513
VITC OUT
For selecting how to output the VITC which is
superimposed on the output video signal.
0000 SBC
In the playback mode, the time code recorded in
the SBC area is output.
0001 VAUX
In the playback mode, the time code recorded in
the VAUX area is output.
<Note>
z The VITC information detected by the HD serial
input is automatically recorded in the VAUX area
when the video signals are recorded.
z When [23/24], [25 (HD)], [25 (SD)], [50 (HD)], or
[50 (SD)] is selected in System Menu No. 25
(SYSTEM FREQ) and [VAUX] is selected, the
output time codes may not be consecutive.
514
HD EMBD
VITC
For selecting whether to superimpose the VITC
information on the HD serial output.
0000 OFF
The VITC information is not superimposed.
0001 ON
The VITC information is superimposed.
515
HD EMBD LTC
For selecting whether to superimpose the LTC
information on the HD serial output.
0000 OFF
The LTC information is not superimposed.
0001 ON
The LTC information ist superimposed.
516*
1
TC OUT ADV
For selecting the processing to align the phase
of the time code which is output from the TIME
CODE OUT connector.
Normally, the time code which is output from the
TIME CODE OUT connector is aligned with the
output video and audio. If so required by the
connection with an external component or for some
other reason, this item makes it possible to set the
mode for aligning the phase with the input.
0000 OFF
The phase alignment processing is not con-
ducted. The time code which is output from the
TIME CODE OUT connector is aligned with the
output video and audio.
0001 EDIT
During playback when an editing mode has been
selected and during editing, the time code which
is output from the TIME CODE OUT connector is
aligned with the input video and audio. In all
other modes, it is aligned with the output video
and audio.
517*
1
TCG OUT
For selecting whether to latch the TCG display
and LTC output during INPUT CHECK.
0000 MOMENT
The INPUT CHECK mode is established only
while the INPUT CHECK key is held down.
0001 LATCH
When the INPUT CHECK key is pressed, the
INPUT CHECK mode is established; even when
it is released, the mode remains unchanged.
The selection is released when the video output
is set to a mode other than the EE mode.