Filter
Top Products
94
Setup menus (continued)
<TIME CODE>
*1 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or 50 Hz
(HD, SD) mode is selected in System Menu No. 25 (SYSTEM
FREQ), this item is not displayed.
*2 When the 23/24 Hz mode, 25 Hz (HD) mode, or 50 Hz (HD)
mode is selected in System Menu No. 25 (SYSTEM FREQ),
this item is not displayed.
The underlining (__) denotes the factory setting mode.
No./Item Description of setting
500*
2
VITC BLANK
For selecting whether or not to output the VITC
signal at the positions selected by setup menu
items No.501 (VITC POS-1) and No.502 (VITC
POS-2).
0000 BLANK
The VITC signal is not output.
0001 THRU
The VITC signal is output.
<Note>
Only the SD output takes effect at this setting.
501*
2
VITC POS-1
For setting the position where the VITC signal
is to be inserted.
<59/60Hz> <50Hz>, <25Hz(SD)>, <50Hz(SD)>
0000 10L
: :
0006
16L
: :
0010 20L
0000 7L
: :
0004
11L
: :
0015 22L
<Notes>
z The same line as the one selected by the setup
menu item No.502 (VITC POS-2) or
No.692(UMID POS) cannot be selected.
z Only the SD output takes effect at this setting.
502*
2
VITC POS-2
For setting the position where the VITC signal
is to be inserted.
<59/60Hz> <50Hz>, <25Hz(SD)>, <50Hz(SD)>
0000 10L
: :
0008
18L
: :
0010 20L
0000 7L
: :
0006
13L
: :
0015 22L
<Notes>
z The same line as the one selected by the setup
menu item No.501 (VITC POS-1) or
No.692(UMID POS) cannot be selected.
z Only the SD output takes effect at this setting.
503*
1
TCG MODE
For setting the synchronization of the internal
time code generator.
0000 REGEN
The time code reader is synchronized with the
time code which is read from the tape.
0001 PRE
Presetting is enabled at the operation panel or by
the remote controller.
0002 AUTO
The REGEN and PRE settings are automatically
switched in accordance with the operation mode.
In the editing mode: REGEN is selected.
In all other modes: PRE is selected.
504*
1
RUN MODE
For setting when the internal time code
generator is to advance depending on the
operation mode.
0000 REC
The time code generator is advanced during
recording.
0001 FREE
The time code generator is advanced while the
power is on regardless of which operation mode
is established.
No./Item Description of setting
505*
1
TCG REGEN
For selecting the regeneration signal when
REGEN has been selected as the TCG (time
code generator) mode.
0000 TC&UB
Regeneration applies to both the time code and
user bits.
0001 TC
Regeneration applies only to the time code only.
0002 UB
Regeneration applies only to the user bits only
506*
1
REGEN MODE
For selecting the editing mode range when the
VTR is operating in the REGEN mode while
performing editing operations with “AUTO”
selected as the setup menu item No.503 (TCG
MODE) setting.
0000 AS&IN
Regeneration applies during assemble or insert
editing.
0001 ASSEM
Regeneration applies during assemble editing.
0002 INSRT
Regeneration applies during insert editing
507*
1
TC SOURCE
For selecting the time code to be used when
HDSDI or SDSDI has been selected as the setup
menu item No.600 (VIDEO IN SEL) setting when
an external time code is to be used.
[When HDSDI has been selected]
0000 INT
The time code of the internal time code genera-
tor is used.
0001 EXT_L
LTC of the TIME CODE IN connector is used.
0002 SLTC
The LTC information added to the serial signals
which are input to HD SDI IN is used.
0003 SVITC
The VITC information added to the serial signals
which are input to HD SDI IN is used.
[When SDSDI has been selected]
0000 INT
The time code of the internal time code genera-
tor is used.
0001 EXT_L
LTC of the TIME CODE IN connector is used.
0002 VITC
The VITC information added to the serial signals
which are input to SD SDI IN is used.
<Notes>
z If the VIDEO IN SEL input selection is changed,
the time code is converted as shown below.
[HDSDI]
<>
[SDSDI]
INT
<>
INT
EXT_L
<>
EXT_L
SLTC
<>
EXT_L
SVITC
<>
VITC
z When [1394] is selected in Setup Menu No. 600
(VIDEO IN SEL), the time code input for the
IEEE 1394 digital input/output connector is used.
However, the VITC information is not
superimposed on the video signal during EE
mode and when recording. Furthermore, LTC
information and VITC information are not
superimposed on the HD serial output.