Filter
Top Products
89
Setup menus (continued)
<OPERATION> (continued)
*1 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or 50 Hz
(HD, SD) mode is selected in System Menu No. 25 (SYSTEM
FREQ), this item is not displayed.
No./Item Description of setting
118*
1
SP MODE
INH
For selecting whether to allow or inhibit
recording on a tape which has been written by a
format other than DVCPRO HD-LP.
0000 OFF
Recording on the cassette tape is allowed.
0001 ON
Recording on the cassette tape is inhibited.
<Note>
When [OFF] is selected, the inhibition/permission
state for recording to a cassette tape follows Setup
Menu No. 113 (REC INH).
119*
1
CONFI REC
For selecting whether or not to perform simul-
taneous playback during normal recording.
0000 OFF
According to the settings in Setup Menu No. 140
(OUTPUT), the simultaneous playback operation
during normal recording shifts.
EE EE output
TAPE Simultaneous playback output
0001 ON
Regardless of the settings in Setup Menu No.
140 (OUTPUT), simultaneous playback is always
applied during normal recording.
131
PAGE MODE
For selecting what cue point operation is to be
performed when the multi cue function has
been set to ON.
0000 MANU
Operation is confined within the selected page,
and 6 cue points can be registered.
0001 AUTO
When the page whose cue points are being reg-
istered becomes full, operation is automatically
transferred to the next page, and registration is
continued. A total of 60 cue points on up to 10
pages can be registered.
132
ROTA MODE
For selecting whether to perform the
registration operation if all the cue points have
already been registered when the multi cue
function has been set to ON.
0000 OFF
No further cue points are registered.
0001 ON
The registration operation is continued. If “MANU”
has been selected as the setup menu item No.131
(PAGE MODE) setting, the next cue point is
registered at CUE
¢
1 on the page concerned; if
“AUTO” has been selected, it is registered at CUE01.
133
KEY BEEP
For setting the volume of the sound heard when
the keys are touched.
0000 OFF
0001 LOW
0002 HIGH
134
ALARM BEEP
For setting the volume of the alarm tone.
0000 OFF
0001 LOW
0002 HIGH
<Note>
If the fan motor has shut down, the alarm tone is
sounded at the HIGH volume level regardless of
this setting.
No./Item Description of setting
140*
1
OUTPUT
For selecting the output signals.
0000 EE
The input signals selected by setup menu items
No.600 (VIDEO IN SEL) and No.713 (CH1 IN
SEL) to No.724 (D IN SEL 78) are output.
0001 TAPE
<In the STOP mode>
The signals played back from the tape are output.
<During recording or editing>:
The simultaneous playback signals are output.
<Note>
Output signals when recording and editing are
selected in Setup Menu No. 119 (CONFI REC)
and No. 302 (CONFI EDIT).
141*
1
VOLUME
For setting what is to be controlled by the audio
volume controls on the front panel.
0000 REC
The controls function as REC volume controls.
0001 PB
The controls function as PB volume controls.
0002 AUTO
Normally, the controls function as PB volume
controls. However, during recording or in the EE/
INPUT CHECK status, they automatically func-
tion as REC volume controls.
142*
1
AUDIO UNITY
For selecting the conditions under which the
AUDIO UNITY lamp on the front panel is to light.
0000 IN
The lamp lights when all the audio input levels
are set to the UNITY level.
0001 OUT
The lamp lights when all the audio output levels
are set to the UNITY level.
002 IN/OUT
The lamp lights when all the audio input and out-
put levels are set to the UNITY level.
143
CASSTT
LIGHT
For setting whether the lighting of the tape
mechanism is to be set to ON or remain OFF.
0000 OFF
The mechanism does not light even when a cas-
sette is inserted.
0001 ON
The mechanism lights when a cassette is
inserted.
144
TC INPUT
For switching the preset registration method for
the time code.
0000 NORMAL
The time code is input starting with the left-most
digit.
0001 REV
The time code is input from the high-order digit
but is displayed from the right-most digit.
145
FRONT LCD
For selecting whether the LCD monitor display
on the front panel is to be turned on or off.
0000 OFF
The display is turned off.
0001 ON
The display is turned on or off in synchronization
with the screen saver operation for the time code
display area.
146
SAVER DISP
If the front operation or tape operation is not
executed for some while, the time code display
switches to the screen saver display.
For selecting the screen saver display format.
0000 BLACK
To the black display
0001 LOGO
To display [EX] logo animation