Filter
Top Products
70
CHANGING THE INITIAL SETTINGS (cont.)
6
Press the number button “0” to select “TV PROG”
or “SAT.”
• In this example, select “TV PROG.”
• Select “SAT” to enter a programme position
number of the satellite receiver.
7
Press
∞
or
5
to enter the
programme position
number for the station of
the selected Guide
Program number, then
press ENTER.
This is the number you select
on this unit or on the satellite
receiver to tune into the
station.
• To timer-record a satellite
programme with the VIDEO P
LUS
+
®
system, install
the supplied satellite controller and perform the
procedure described on page 17.
8
Repeat steps 5 to 7 to store more Guide Program
numbers.
9
Press SET UP twice to finish the setting.
Setting the built-in TV tuner
It is required to memorize all necessary stations in the
programme positions in order to record TV programmes.
Set the built-in TV tuner manually only in the following
cases.
• When Auto Channel Set has not been performed
correctly by Auto Setup or TV-Linked Setup.
• When you have moved to a different area or if a new
station starts broadcasting in your area.
To set the built-in TV tuner automatically—Auto
Channel Setup
Auto Channel Setup automatically assigns the
programme position numbers to all receivable stations
(their Guide Program numbers are also set automatically)
during Auto Channel Setup in your area. These stations
stored in the programme positions can be selected by
using the
HDD/TV PR +/–
buttons (without going
through any vacant programme positions).
1
Press SET UP.
2
Press
3
or
2
to move
to “INITIAL SET UP,” then
press
∞
.
3
Press
3
or
2
to move
to “TUNER SET,” then press
ENTER.
4
Press
∞
or
5
to move
to
“AUTO CH SET,” then
press ENTER.
5
Press
∞
or
5
to move
to
either “AUTO SET” or “T-V
LINK,” then press ENTER
or
3
.
Auto Channel Setup starts.
• If you have connected
the unit to a TV offering
T-V Link via a 21-pin
SCART cable, select “T-V
LINK.”
• As Auto Channel Setup
progresses, the “ ” mark
on the AUTO SET screen
moves from left to right.
When Auto Channel
Setup is finished, the
confirmation screen
appears after the message
“SCAN COMPLETED.”
• The stations the unit has located appear on the
confirmation screen— programme positions (PR),
station channels (CH) and station names (ID—see
pages 73 and 74).
The confirmation screen and the programme
currently being broadcasted by the flashing station
appear alternately for about 8 seconds each. To
view the other stations preset in the programme
positions, press
3
/
2
/
∞
/
5
.
6
Press SET UP three times to finish the setting.
NOTES
•Using the confirmation screen, you can skip or add stations,
enter station names and perform other operations. Refer to
pages 71 to 73 for the procedures.
•This unit memorizes all detected stations even if reception of
some of them is poor. You can delete those stations with an
unacceptable picture (see page 71).
•Depending on reception conditions, stations may not be stored
in order, and the station names and/or the Guide Program
numbers may not be stored correctly.
If the Guide Program numbers are not set properly when you
timer-record a TV programme using the VIDEO P
LUS
+
®
system,
the unit will not record a TV programme you want (see page
40).
•Fine tuning is performed automatically during Auto Channel
Set. If you want to perform tuning manually, see page 72.
•If “SCAN COMPLETED –NO SIGNAL–” appears on the TV,
make sure of the aerial connection, then press
ENTER
; Auto
Channel Set will take place again.
[ENTER]
[SET UP]
(Example) If CH4 is received
on channel position
4.
TUNER SET
AUTO CH SET
MANUAL CH SET
[ENTER]
[SET UP]
[SET UP]
BBC1
BBC2
ITV
CH4
CH5
26
33
23
30
37
[ENTER]
[CANCEL]
[SET UP]
End
Beginning