LG Electronics STB-2000 DVR User Manual


  Open as PDF
of 86
 
21
206-4256
(Continued from previous page)
IP Conguration
a) In the Media Type eld,use the Left/Right arrow keys to
select IP.
Note:Bydefault,thePro:CentricManualConguration
screeninitiallyshowsRFcongurationelds.Whenyou
select “IP” as the Media Type, the Data Channel and
SignalStrengtheldsarereplacedwith(IP)Addressand
Portelds.
b) IntheAddressandPortelds,eitherkeyinorusethe
Left/Right arrow keys to select the appropriate values for
the Pro:Centric server IP address and port number.
The IP address must match the IPv4 multicast address
and the port number must match the port number that is
set in the Pro:Centric server.
4. Oncealleldsarecompletedasrequired,youhave two
options (see also note below):
• To save the data entered and exit the wizard, use the arrow
keys to select Exit and then press OK. In the subsequent
pop-upconrmationwindow,selectSave and Exit, and then
press OK once more. The Pro:Centric application and/or
E-Z Installation data will be downloaded to the STB at a later
time. This option is useful, in particular, if the Pro:Centric
serverhasnotyetbeencongured.
• To initiate a real-time download of Pro:Centric application
and/or E-Z Installation data, use the arrow keys to select
Next, and then press OK.
The EZ-Manager Wizard will proceed with the remaining
Pro:Centric application and/or E-Z Installation data down-
load steps, as shown on the Processing the Pro:Centric
Congurationscreen.
Note:WithRFconguration,Pro:Centricserverdatamust
be present on the RF channel selected as the STB’s Data
Channel in order for you to select “Next” (you will see a
“Data Channel found” message below the signal strength
indicator).WithIPconguration,Pro:Centricserverdata
must be present via the wired LAN cable connection in order
for you to select “Next” (you will see an “IP server found”
messagebelowthePorteld).
WhenthePro:Centriccongurationiscomplete,anEZ-Manager
CongurationCompletescreenisdisplayed,andafter10
seconds, the wizard exits, and the STB turns OFF.
Note:WiththeEZ-ManagerCongurationComplete screen on
display, you also have the option to manually turn off or reboot
the STB. If desired, select Turn Off or Reboot, respectively, and
then press OK on the Installer Remote.
EZ-Manager Wizard (Cont.)
EZ-Manager Wizard
EZ-Manager Configuration Complete
Pro:Centric Application
Maintenance Files
GEM application downloaded
STB-2000_Config.tlx
Installed Components
2
1
3
The TV will turn off in 3 second(s).
4
Reboot
Turn Off
EZ-Manager Wizard
Processing the Pro:Centric Configuration...
Application files
Maintenance files
Warning - Do not remove AC power or the signal cables during these steps
1%
In progress...
Pending...
Retrieving files from data channel 75
4
2
1
3
Downloading the Pro:Centric application files takes a few minutes.
Please wait...
EZ-Manager Wizard
Pro:Centric Mode
Channel Number
Signal Strength
Signal Quality
0%
GEM
1
< >
Back
Next
Exit
Pro:Centric Manual Configuration
0%
No signal
Are you sure you want to exit the wizard?
If you select ‘OK’ now, your settings will be lost
and you will exit the setup wizard.
This window will close and you will be returned to
the previous page automatically in 2 seconds.
Save and Exit
Cancel
OK
!
4
3
2
1
EZ-Manager Wizard
Pro:Centric Mode
Media Type
Addresss
Port
GEM
IP
< >
Back
Next
Exit
Pro:Centric Manual Configuration
255
0
255255255
Pro:Centric Manual Configuration Screen with
IP Media Fields
4
3
2
1
 previous next