Filter
Top Products
33
206-4256
103 - ATSC TUNE MODE
Sets ATSC tuning mode. Default set to 1 for Physical Channel
scan. Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets Minor Start Channel number at power up. 0 = NTSC. If not
0, number selected is the digital channel’s Minor Start Channel
number.
Note: This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 0 or 255.
105 - VID OUT FORMAT
Selects the format for video output (i.e., the screen resolution):
1 = 720p (default) 4 = 1080p 5 = 1366 x 768
If you change the video output format, once you exit the STB
Installer Menu, the STB will reboot to change to the new video
output resolution.Whentherebootiscomplete,aconrmation
pop-up window for the resolution will be displayed on the screen.
See “Setting the Video Output Resolution” on page 14 for further
information.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to
retain default aspect ratio with power off. See item 096 DEF. ASP.
RATIO above.
108 - PANEL COM (Panel Communication)
Sets the display panel baud rate:
0 = 1200 1 = 2400
2 = 9600 (default) 3 = 115200
110 - PANEL DELAY
Sets the delay time in seconds before the STB initiates communi-
cation with the display panel after the STB/display is turned ON. 8
seconds is the default.
113 - PANEL TYPE
Selects the display panel type. This setting is only applicable for LG
Public Display TVs and Commercial Monitors that use the DISPLAY
CONTROL 1 port for STB-to-display panel communication. The
default value (4) will be appropriate for most of these display types.
SeeReferencesection,“DisplayPanelSpecications,”todetermine
the appropriate setting for the display panel being used.
116 - VIDEO MUTE EN (Video Mute Enable)
Applicable for analog channels only. If set to 1, video mutes
(blank screen) when no signal is present.
117 - FACT DEFAULT (Factory Default)
Set to 1 and press OK to restore the factory default settings of all
Installer Menu items. Once complete, the value returns to 0.
Caution: If set to 1, this clears all STB Installer Menu
custom settings and restores the factory default
settings. It also clears the channel lineup, including
any assigned channel icons and custom text labels.
Note: See also Reference section, “Restoring Factory Defaults on
the STB(s),” for further information.
119 - DATA CHANNEL
Set to 0 to disable. Set from 1 to 135 to match the RF channel
number that will be used by the Pro:Centric server as its data
channel. If left at the default value (255), the STB’s Data Channel
Auto Search feature will be enabled (see additional information
below). *
Data Channel Auto Search feature: When this item is set to 255
(default), once every 24 hours, the STB will initiate a search of 10
predenedchannels(10,20,30,...100)andthen,ifnecessary,
perform a complete search of the RF channels (1 to 135) in an
attempttondtheRFchannelusedbythePro:Centricserveras
its data channel. If the Pro:Centric RF channel is found, the DATA
CHANNEL value will be changed from 255 to match the server’s
RF channel number. The time at which the Auto Search occurs
depends on the setting of item 121 UPDATE TIME HR. See item
121 description for further information.
Note: Pro:Centric updates are downloaded from the Pro:Centric
server to the STB when the STB/display panel is turned OFF.
While Pro:Centric updates are in progress, it is not possible to
turn ON the STB/display.
Note: The Data Channel is automatically set to “253” if Media
Type is set to “IP” either in the EZ-Manager Wizard or in the
STB’s IP Environment / Pro:Centric Menu (see “EZ-Manager
Wizard” on pages 15 to 22 or “Pro:Centric Setup” on pages 60
to 61, respectively) or if Installer Menu item #119 Data Channel
is set to “IP Address” in the FTG File Manager, which is used to
congureSTBCPUsforFTGModeoperation.Itisnotpossibleto
change the value to “253” directly in the Installer Menu.
Installer Menu (Cont.)
* PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.