Filter
Top Products
Chapter 3 Preparations
3-20 (E) 3-4 Setup
013
014
015
BI
PB/EE SELECT P1
PB/EE SELECT P2
PB/EE SELECT P3
For the PANEL, DTR+PANEL, DTR+DTR and BVE modes, specifies when the PB port
enters the state indicated by SETUP MENU 108 AUTO EE SELECT, and whether it
should automatically correspond to the REC port.
: Always output at the PB side.
PB/EE : Switch to the REC side according to the SETUP MENU 108 status.
Note: In the BVE mode, “PB/EE SELECT P2” item (menu 014) is disabled.
016
BI
CHARACTER POSITION V
SHIFT
The vertical position of text display of time codes output from the MONITOR OUT
terminal, SDI (SUPER) and ANALOG COMPOSITE (SUPER) terminals, can be more
minutely adjusted than is possible with SETUP MENU 003.
.. 20
019 SYSTEM OPERATE
CONFIGURATION
Select the application mode for this unit.
: All ports are controlled only from the optional BKMA-505
DTR + PANEL: Controls R1 and P1 with the DTR-3000, controls R2 and P2 (or P2 and
P3) from the BKMA-505.
DTR + DTR : The R1/P1 and R2/P2 pairs are controlled by two DTR-3000 units.
BVE : R1 and P1 are controlled as an RP port by the editor.
022
BI
ERROR INFORMATION
SELECT
Activate or deactivate various status information display output from the MONITOR
OUT connectors of the SDI (SUPER) or ANALOG COMPOSITE (SUPER) connectors.
Note: This setting item takes priority over the system setup panel CHARACTER
switch setting.
SUB MENU
ERROR/WARNING Specifies whether the ERROR/WARNING display is on or off.
off
Note: Even if this is set to “on”, the warning message “Ref. Missing” is not
displayed.
NOT ENOUGH SPACE Specifies whether a warning message is displayed when there remains approximately
five minutes of recording time on the HDD.
off
027 – FAST REBOOT Carry out a fast reboot of the system. This is faster than switching the system off and on
again, because the HDD power supply is not turned off.
Start : Start reboot.
I SUB MENU
EXECUTE
028 AUDIO BIT LENGTH Select the word length for audio sampling.
16 bits
Notes: • Bit length cannot be set for individual lots of material.
• After changing the settings for this item, all material must be erased using
-ALL ERASE (menu 099).
030
B
GOOD SHOT PARAMETER Specifies the partial save method to use for Replay scenes with the DTR-3000, for
highlight editing with DTR+Panel and DTR+DTR modes.
SUB MENU
SAVE DUR. (1 .. .. 255) Specifies the partial save duration, in seconds.
TRIM SIZE (0 .. .. 15) Specifies the trim length to be added before and after the partial save period.
AUTO SAVE Specifies the trigger command to start partial saving.
: Partial save disabled
cue up with data : Start partial save after cue up.
CUEUP SELECT Specifies the time data at which to perform cue up in DTR+PANEL or DTR+DTR
mode.
: Regardless of the timer mode, cue up is performed with TM2 (FTC).
timer mode : Cue up is performed according to the timer mode.
Notes: • When using the DISK INDIVIDUAL MODE of the DTR-3000, select
“FTC”. However, select “timer mode” in the following cases:
- When performing direct cue up in 205 point mode from the keypad.
- When performing cue up in 10 point mode with SERACH + CUEn.
• When using a controller other than the DTR-3000, select “timer mode”. In
this situation it is not possible to use the GOOD SHOT function, so set the
AUTO SAVE item (menu 030) to “off”.
Basic menu items (Continued)
Item number Display indication Settings
PB
0
PANEL
on
on
20 bits
5
5
off
FTC