Filter
Top Products
Appendixes
Error Messages A-3 (E)
P3 port Warning
Meaning: Detected a malfunction in the P3 port control
area.
The DM-127 Board and DPR-189 (B) Board
may be defective.
RAID SBX(U) Warning
Meaning: Detected a malfunction in communications
between the FM-81 Board and RAID.
The FM-81 Board and PU-121 Board may be
defective.
RAID SBX(D) Warning
Meaning: Detected a malfunction in communications with
the FM-81 Board in the PU-121 Board.
The FM-81 Board and PU-121 Board may be
defective.
RAID Battery Warning
Meaning: Detected a malfunction in the battery that
maintains PU-121 Board settings.
The battery may be discharged.
RAID Flash Warning
Meaning: A Flash ROM malfunction detected in the PU-
121 Board.
The PU-121 Board may be defective.
HDD xx Warning
Meaning: Errors occur frequently while reading/writing
HDD number xx.
HDD xx Fail
Meaning: HDD number xx cannot be used due to
malfunction.
HDD xx Unknown HDD
Meaning: HDD number xx has not been recognized yet.
This message appears when a new replacement
HDD is inserted.
Remedy: Run -NEW HDD (menu 098) from the base
menu and restore AV data to the new HDD.
During restoration, “Rebuilding” is displayed
on the front panel. Do not turn off the power
until restoration is complete.
HDD xx SPC Error
Meaning: SPC connected to HDD number xx is not usable
due to malfunction.
The IF-837 Board may be defective.
HDD xx No HDD
Meaning: No HDD is inserted in HDD slot number xx.
EM Router Init. Fail
EM Router Init. Fail
Meaning: The video router on the EM-3 board cannot be
initialized. The EM-3 board may be defective.
TM Warning LTC
Meaning: Either the correct time code signal is not being
input to the TIMECODE IN (SYSTEM) jack on
the rear panel, or there may be a hardware
problem with the LTC Reader IC on the FM-81
board.
* Only a 1× time code signal can be input to the
TIMECODE IN (SYSTEM) jack.
Remedy: Check the signal that is being input to the
TIMECODE IN (SYSTEM) jack. If the correct
signal is being input, there may be a hardware
problem with the LTC Reader IC (IC1101) on
the FM-81 board.
EM Recorder Init. Fail
Meaning: Was unable to initialize the RP port on the EM-
3 board in the BVE mode.
EM Mixer Config Fail
Meaning: Detected a malfunction in communications
between the EM-3 Board and the DSP.
The EM-3 Board may be defective.
Temperature Rise
Meaning: The internal temperature of the unit is too high.
If the unit is being used in a normal temperature
environment, this error may indicate that the fan
is not functioning properly.
Remedy: Confirm that no fan warning has been output.
LoopRec Will Stop
Meaning: The remaining available recording space is
exceeded and partial save performed during
loop recording. If recording continues, the
available recording space becomes insufficient
and recording is stopped.
Remedy: To continue recording, delete the partially saved
file or the unnecessary unedited file to create
space. Once the file is deleted and the warning
display disappears, it is possible to continue
loop recording.
Material Entry Full
Nearly Rec Stop
Rec Stopped
Not enough Space To Rec
Too Much Fragmentation
Temp. File Protected
These are all special errors that may occur while editing in
BVE mode. For details on these errors, refer to Section 5-
5-9, “Editing-Related Error Messages” (page 5-9).
EF-30 Boot Fail
EF-30 ConfgFail
EF-31 ConfigFail
These errors can occur only with the BKMA-560 or
BKMA-561 installed, and indicates that the EF-30 board
or EF-31 board has malfunctioned.