Filter
Top Products
Chapter 5 Basic Functions of Each Mode
5-5 Basic Operations in BVE Mode 5-7 (E)
4
To begin recording, hold down the REC key on the
control panel and then press the PLAY key.
• Recording starts from the cued up position in the
file that is currently loaded. Previously recorded
contents are overwritten.
5
To stop recording, press the STOP key.
• The STOP key can also be pressed after the length
of the original file has been exceeded.
• Pressing the STOP key is the only way to halt
recording; pressing PLAY or any other keys will
not halt recording.
5-5-3 Basic Operation of the R2 Port
In BVE mode, the R2 port is a collection-only port.
Immediately after the MAV-555SS is started up in BVE
mode, the recording file is automatically loaded to the R2
port; recording may then begin at any point thereafter.
Collecting through the R2 Port
x When performing the operation through the
control panel
1
Press the R2 button on the control panel to select the
R2 port.
2
While holding down the REC key on the control
panel, press the PLAY key.
Recording begins. While recording is in progress, a
red z lights in the status display area for the R2 port
on the display panel.
3
To stop recording, press the STOP key.
Recording stops and the red z in the status display
area disappears. Recording can be resumed at any
time by holding down the REC key and pressing the
PLAY key. Repeatedly starting and stopping
recording will produce sequential collection at the
end of the same file.
x When performing the operation through the
MAVE-F555
1
Press the B key and the z key on the MAVE-F555
simultaneously.
2
To stop recording, select the BG port and then press
the x key.
Repeatedly starting and stopping recording will
produce sequential collection at the end of the same
file.
Replacing Files through the R2 Port
x When performing the operation through the
control panel
Follow the procedure described below through the control
panel in order to replace the file collected in the R2 port
with a new file.
1
Press the R2 button on the control panel to select the
R2 port.
2
On the control panel, hold down the SHIFT key and
press B1 (Unload). The file is unloaded and a new file
for collection is automatically loaded to the R2 port in
its place.
x When performing the operation through the
MAVE-F555
When performing the replacement operation through the
MAVE-F555, press the x key while holding down the z
key in order to first unload the file collected in the R2 port
and then replace it with a new file. When performing this
operation, the BG port must be selected and the unit must
not be recording.
Note
If you have just collected important information, be sure to
confirm the file number and file name in the R2 port before
unloading the file.
In addition, when using the control panel, we recommend
using the RENAME function to change the file name
while recording is in progress. When using the MAVE-
F555, we recommend registering the file with the
MEMORY key.
For details on control panel operation, refer to the BKMA-505
operation manual.
For details on MAVE-F555 operation, refer to the MAVE-F555
operation manual.
5-5-4 Basic Operation of the P2 and
P3 Ports
The P2 port operates in the same manner in BVE mode as
it does in panel mode. It can be used as the PLAYER side
for linear editing and as an output port. When using a 2
input/2 output configuration, the file being collected
through the R2 port can also be loaded to the P2 port.
Furthermore, when using a 1 input/3 output configuration,
output through the P3 port can be controlled through the
control panel or the MAVE-F555.
Connect the RS-422 cable for the P2 port to the REMOTE
IN4 connector.
Connect the RS-422 cable for the P3 port to the REMOTE
IN3 connector.