Filter
Top Products
Chapter 3 Preparations
3-4 Setup 3-39 (E)
806
BI
SHUTTLE MUTING This item specifies audio muting during shuttle operations.
: Audio is always output.
on : Muting is always applied.
809 AUDIO MONITOR MUTING This item specifies the muting of the audio output from the audio monitor.
: Outputs audio normally.
muting : Mutes the audio output.
820
BI
AUDIO OUTPUT MIXING This item specifies the mixing method when mixing the audio output by the PB ports.
add : Simple addition
average : Average
: Root mean square
821
822
823
BI
AUDIO OUTPUT CHANNEL P1
AUDIO OUTPUT CHANNEL P2
AUDIO OUTPUT CHANNEL P3
These items make the settings for substituting, mixing and outputting the audio
output by the PB ports on each channel.
SUB MENU
CHANNEL 1 Select from among none, , 2, 12, 3, 13, 23, 123, 4, 14, 24, 124, 34, 134, 234, and
1234. The displayed channels are mixed and output.
CHANNEL 2 Select from among none, 1, , 12, 3, 13, 23, 123, 4, 14, 24, 124, 34, 134, 234, and
1234. The displayed channels are mixed and output.
CHANNEL 3 Select from among none, 1, 2, 12, , 13, 23, 123, 4, 14, 24, 124, 34, 134, 234, and
1234. The displayed channels are mixed and output.
CHANNEL 4 Select from among none, 1, 2, 12, 3, 13, 23, 123, , 14, 24, 124, 34, 134, 234, and
1234. The displayed channels are mixed and output.
824
BI
AUDIO EDIT PREVIEW
SWITCHER
Sets the output phase of the Audio playback signal for the Edit Preset Status.
: Matches the output phase during EE. Set when previewing the
MAV-555SS or while monitoring the VTR output signal.
external switcher : Matches the internal or external video code. Set when switching the
signal with the external switcher and Previewing.
827
828
829
BI
AUDIO OUTPUT PHASE P1
AUDIO OUTPUT PHASE P2
AUDIO OUTPUT PHASE P3
Sets the output timing of the audio playback signal (SIF, AES/EBU only). With 0x100 as
the reference, as it becomes smaller, the output timing comes earlier, and as it becomes
larger, the output timing comes later.
0×000 .. .. 0×1ff
880
881
882
BI
INTERNAL AUDIO SIGNAL
GENERATOR R1
INTERNAL AUDIO SIGNAL
GENERATOR R2
INTERNAL AUDIO SIGNAL
GENERATOR R2
Selects the device to generate the internal audio test signal.
: No audio test signal is generated.
silence : Silent signal.
1 KHz sine : Generates a sine wave of 1KHz - 20dB FS.
1 KHz-9 dB: Generates a sine wave of 1KHz - 9dB FS.
When not off
For any selection other than “off”, press the INPUT SELECT button on the front panel to
switch the button on, and then press and hold down the CH1 AUDIO INPUT button for 3
sec. or more to switch all of the digital audio input signals for all channels to the internal
audio SG.
883
884
BI
EMPHASIS ON/OFF R1
EMPHASIS ON/OFF R2
When the BKMA-513 optional board is installed, these items enable and disable pre-
emphasis for each individual port.
on
886
887
888
BI
RATE CONVERTER R1
RATE CONVERTER R2
RATE CONVERTER R3
Specifies whether an audio AES/EBU rate converter is used.
: Uses a rate converter.
disable : Does not use a rate converter.
950
B
SS CAMERA SELECT Sets the input video format from cameras that support Super Slow.
: Records video signals from standard format Sony cameras.
other : Records video signals from cameras other than standard format Sony
cameras.
951
BI
SS AUDIO INPUT DELAY
ADJUST
Sets the timing of the input audio signal with Super Slow recording.
000 .. .. 1FF
Note: If you set SS LIP SYNC ADJUST (menu 953) to on, be sure to adjust this
setting.
Expansion menu items (Continued)
Item number Display indication Settings Description
off
normal
rms
1
2
3
4
internal
0×100
off
off
enable
sony
100