Filter
Top Products
Chapter 5 Basic Functions of Each Mode
5-4 (E) 5-4 Basic Operations with DTR+Panel and DTR+DTR Modes
2
Assuming it is okay to delete all material on this unit,
execute ALL ERASE (menu 099) on the basic menu,
and reboot the unit.
* If you don’t want to delete all material, change this unit
to the Panel mode, delete the “LIVE1” (and “LIVE2”)
material, the change back to the DTR+Panel (or
DTR+DTR) mode.
For basic menu operations, please see Section 3-4-2, “Basic Menu
Operation” (page 3-23).
Note
After changing the recording time (LIVE DURATION),
the materials must be deleted per Step 2 above. It is not
possible to extend the recording time and continue
recording from previously recorded material, or to
otherwise change the recording time in the midst of
recording.
For precautions and setup related to LIVE DURATION, please see
Section 3-4-1, “Basic Menu Settings” (page 3-18).
Loop Recording
During loop recording, when the recording time exceeds
the time set for LIVE DURATION, the oldest recorded
material is overwritten, so that even when the length of the
recording exceeds preset recording time, the most recent
recorded images are always stored up to the time set for
LIVE DURATION.
Loop recording is performed by the following procedure:
1
Set the LIVE DURATION (menu 034) on the basic
menu for DTR-1 (and DTR-2) to the desired time.
2
Set DTR-1 LOOP REC (or DTR-2 LOOP REC) on.
3
Assuming it is okay to delete all material on this unit,
execute ALL ERASE (menu 099) on the basic menu,
and reboot the unit.
* If you don’t want to delete all material, change this unit
to the Panel mode, delete the “LIVE1” (and “LIVE2”)
material, the change back to the DTR+Panel (or
DTR+DTR) mode.
For basic menu operations, please see Section 3-4-2, “Basic Menu
Operation” (page 3-23).
Note
Once material has been recorded, loop recording cannot be
turned on or off until the recorded material is erased.
5-4-2 Basic Operations in
DTR+Panel and DTR+DTR
Modes
After the initial settings described in the previous section,
the following operations can be performed.
Setting the preroll time in SS mode
(DTR+Panel mode)
In SS mode, when setting the preroll time, it is necessary
to specify a value three times larger than that of the desired
time.
Examples
• When you want to specify 10 frames (525)
Input [1S 00F] and the preroll time becomes 10 frames.
• When you want to specify 3 seconds
Input [9S 00F] and the preroll time becomes three
seconds.
Recording from the DTR-3000
1
While holding the SHIFT key, press the REC key on
the DTR-3000.
Recording starts at the recording port of this unit that
is connected to the operating DTR-3000.
2
To stop recording, hold the SHIFT key and press the
STOP key on the DTR-3000.
To resume recording, hold the SHIFT key while
pressing the REC key again.
Refer to the DTR-3000 Operating Manual for further details.
The input signal can be verified at the output terminal by pressing
the REC key by itself.
Re-recording from the beginning of the
recording area
Recording cannot be restarted randomly within previously
recorded material: it is always resumed from the point
where it was last stopped. To re-record from the beginning
of the recording area, perform the following procedure:
1
Assuming it is okay to delete all material on this unit,
execute ALL ERASE (menu 099) on the basic menu,
and reboot the unit.
* If you don’t want to delete all material, change this
unit to the Panel mode, delete the “LIVE1” (and
“LIVE2”) material, the change back to the
DTR+Panel (or DTR+DTR) mode. However, if you
want to retain previously recorded material, rename
it to something other than “LIVE1” or “LIVE2.”
2
Follow the above steps for recording from the DTR-
3000 to re-record.
Recording starts at the beginning of the recording
area.
Playback from the DTR-3000
1
Press the PLAY key on the DTR-3000.
• Playback starts at the playback port of this unit that
is connected to the controlling DTR-3000.