Filter
Top Products
Index
242 UDA2182 Universal Dual Analyzer Product Manual January 2009
PID Alarms...............................................................97
PID B........................................................................94
PID Configuration.....................................................93
PID Control.............................................................107
PID Control 1 Alarm 1 ..............................................60
PID Control 1 Alarm 2 ..............................................60
PID Control 2 Alarm 1 ..............................................60
PID Control 2 Alarm 2 ..............................................60
PID Control Configuration ........................................91
PID Display Editing ..................................................27
PID Displays.............................................................26
PID Tuning...............................................................96
Pipe Mounting ..........................................................13
Power Mode.............................................................94
Power Out................................................................94
Power Requirements..................................................6
Power Supply/Analog Output/Relay Output Card...132
Power Wiring............................................................15
Power Wiring Considerations...................................17
Preamplifier Input Option............................................6
Precision Check Resistor ...............................196, 213
Pressure Calibration...............................................163
Pressure Calibration Method..................................168
Pressure Type..........................................................71
Probe Bias Scan ....................................................171
Probe Calibration Diagnostics................................190
Probe Current Too High.........................................190
Probe Current Too Low..........................................191
Probe Current Too Low..........................................190
Probe Extract Timeout ...........................................191
Probe Insert Timeout..............................................191
Probe Pv N Fault....................................................189
Probe Temp N Fault...............................................189
Probe Transit............................................................30
Procedure for Calibrating Analyzer Outputs...........178
Procedure for Calibrating the Temperature Inputs 183,
186
Process Instrument Explorer Software.....................47
Process Variable Source....................................81, 93
Process Variable Values..........................................24
Proportional (P)........................................................91
Proportional Band (PB) ............................................96
PTS OVERRANGE ................................................190
PTS UNDERRANGE..............................................190
Pulse Output ................................................75, 76, 79
PV Bias ....................................................................70
PV High....................................................93, 100, 102
PV Low.....................................................93, 100, 102
PV n INPUT OPEN ................................................189
PV n OVERRANGE ...............................................189
PV n UNDERRANGE.............................................189
PV Source..........................................................76, 77
PV Temperature.......................................................24
PV Type .................................................62, 64, 67, 70
R
Range High ..............................................................73
Range Low...............................................................73
Rate 2 ......................................................................97
RATE action.............................................................96
Ratio.........................................................................94
Readings Unstable.................................................191
READINGS UNSTABLE ........................................190
Rear Panel Support Plate Dimensions.....................12
Recommended wire size..........................................17
Relay outputs .........................................................117
Relay state .............................................................111
Relay States.............................................................42
Relay Types.............................................................76
Relays........................................................................2
Relays Configuration................................................75
Remote Setpoint Permit...........................................95
Remote Setpoint Select ...........................................95
Remote Setpoint Source..........................................94
Repeat per minute....................................................96
Replacement Parts List..........................................194
RESET (Integral Time).............................................97
Reset 2.....................................................................97
Resetting Calibration Trim......................................159
Resetting ORP Offset.............................................153
Resetting Output 1 Offsets.....................................181
Resetting pH Offset................................................162
Resetting pH Offset and (Standardization) pH Slope
...........................................................................147
Resetting Pressure Offset or Bias Volts.................174
Resetting temperature offset..................................185
resume delay..........................................................102
Resume Dly Mins.....................................................30
Rinse Cycle Cnt .......................................................30
Rinse Mins ...............................................................30
RS422/RS485 Modbus RTU Slave Communications
Interface.................................................................6
S
Safety Compliance.....................................................7
Safety precaution .............................................16, 113
Salinity ppt................................................................71
Salinity Type.............................................................71
Sample Calibration.................................................163
Sample Calibration Method....................................166
Sample Method of Calibrating pH Electrodes........145
Sample Method of Calibrating Cation pH ...............160
Sample Tap Electrode Mounting Recommendations
...........................................................................226
Saturation.................................................................70
Sequencer Steps for Auto Cycle ........................32, 35
Serial port.................................................................49
Setpoint at Power up................................................94
Setpoint High Limit Value.........................................93
Setpoint Low Limit Value..........................................93
Setpoint Value..........................................................81
Setup Group Overview.............................................52
Shielded wiring for locations with interference........114
Signal Sources.........................................................57
Single Displays.........................................................25
Slew Time ................................................................73