Filter
Top Products
58
Menu SW On-screen Counter On-screen
No. display display display
[ ] : Factory setting
5-2 MENU SWITCH SETTING CONTENT
5 MENU SWITCH SETTING DETAILS
Switches ON a safety function to prevent
accidental change of input router
OFF:Disactivates this function. Signal is switched
when an input switch is pressed.
ON :Activates this function. To change the input
signal selection, press the input switch while
pressing the [SHIFT] button.
Selects whether or not simultaneous operation of
the player and recorder is permitted by pressing
the [PLAYER] and [RECORDER] buttons together
during swap editing.
ENABLE :Simultaneous operation for the player
and recorder is possible.
DISABLE :Simultaneous operation is not possible.
Before operation, select the VCR with
the [PLAYER] or [RECORDER] button.
369 PARA-RUN [0] [OFF]
1ON
371
INPUT SELECT
[0] [OFF]
SAFETY
1ON
372 P+R AT [0] [ENABLE]
SWAP MODE 1 DISABLE
373 MATCH FRAME [0] [OFF]
1ON
374 MENU OPEN [0] [OFF]
SAFETY 1 ON
This setting determines whether or not the
automatic match frame function is used.
OFF: Match-frame is disabled.
ON : Match-frame is enabled.
After an edit has been executed, the edit-out points
of both the player and recorder are automatically
registered as edit-in points for the next edit.
Selects the method for opening the menu.
OFF:Pressing the [MENU] button engages the
menu switch setting mode.
ON :Pressing the [MENU] + [SHIFT] buttons
simultaneously engages the menu setting
mode.
Allows daisy chaining of several VCR’s via the
[REMOTE IN (9P)] and [REMOTE OUT (9P)]
connectors, enabling you to control all connected
VCRs at the simultaneously.
OFF:Set to this position to control the VCR
independently.
ON :Set to this position for a simultaneous
operation.
Apply this menu setting to all connected VCR's.
Item
Content
Setting
59
5-2 MENU SWITCH SETTING CONTENT
5 MENU SWITCH SETTING DETAILS
<TIME CODE>
[ ] : Factory setting
Menu SW On-screen Counter On-screen
No. display display display
375 AUD EDIT 0
NO DEFINITION
PRESET CH1 [1] [CH1]
2 CH2
3 CH1 OR CH2
376 AUD EDIT 0
NO DEFINITION
PRESET CH2 1 CH1
[2] [CH2]
3 CH1 OR CH2
377 AUD EDIT [0] [NO
PRESET CH3 1 DEFINITION]
378 AUD EDIT 2 CH1
PRESET CH4 3 CH2
CH1 OR CH2
381 JOG FEELING [0] [NORMAL]
(LOCAL) 1 INSENSITIVE
382 9 PIN ID
Ⅲ
---(1ST) 0 0
[15] [F]
383 9 PIN ID-
Ⅲ--
(2ND) 0 0
[1] [1]
15 F
384 9 PIN ID--
Ⅲ-
(3RD) 0 0
[1] [1]
15 F
385 9 PIN ID---
Ⅲ
(4TH) 0 0
[15] [F]
386
MUTING AT NO TAPE
[0] [DISABLE]
1 ENABLE
This mode allows edit controllers that have only two
audio channel capabilities to edit all four audio
channels. The audio insert edit command is
translated using the definition set by this menu to
perform CH1 through CH4 edits.
NO DEFINITION: Accepts no command.
CH1 :Executes insert edit of the channel selected
when the CH1insert command appears.
CH2 :Executes insert edit of the channel selected
when the CH2 insert command appears.
CH1 OR CH2:Executes insert edit of the channel
selected when the CH1 or CH2
insert command appears.
Selects jog dial operation response level.
NORMAL : Normally set to this position.
INSENSITIVE : Slower than NORMAL mode.
Sets the ID reply code when menu switch No.317
<9 PIN DEVICE ID> is set to “3: USER SETTING
(382-385)”. Specify a hexadecimal 4-digit ID code
with these four menu switches (set each digit with
each corresponding menu switch). Select
hexadecimal digits (0 to F).
...
...
...
Even when the PB mode is selected with the [PB
PB/EE] button, the EE mode is engaged when no
tape is loaded.
In this case, this switch is used to select whether
the audio and video signals are output or not.
DISABLE :The audio and video signals are output.
ENABLE :The audio and video signals are not
output.
Item
Content
Setting
...
...
...
...
...