Filter
Top Products
126
3F: Stop Key Basic/JVC-1 Table
Stop
42: CueUp With Data Basic Table
Execute CueUp to the desired point on the tape.
The same as B2: CueUpWithData.
• The VCR returns [01: Complete] after CueUp is
complete.
• When the specified point is not on the tape, the
VCR returns [05: NotTarget].
• Input values of 0 to 9 which follow the second
byte of TxD are expressed with ASCII code.
Auxiliary commands
• [56: Clear] is valid for the second TxD byte or
later. All commands back to the first byte are
cleared.
• When [02: Error] occurs, [41: ClearError] is valid.
The previous command (one byte) is cleared.
• [40: Enter] is valid for the second TxD byte or
later. Whatever has not yet been specified is
regarded as [30: Zero].
4A: Rev-1 Key Basic Table
1x playback in the reverse direction
4B: Rev-4 Key Basic Table
4x playback in the reverse direction
4C: Rev-0.09 Key Basic Table
0.09x playback in the reverse direction
4D: Rev Still Key Basic Table
Still playback
4E: Rev-6 Key Basic Table
6x playback in the reverse direction
4F: Still Key Basic/JVC-1 Table
Still playback
50: In Entry Basic/JVC-1 Table
Registers the current time as IN point.
51: Out Entry Basic/JVC-1 Table
Registers the current time as OUT point.
52: In Flag Reset Basic/JVC-1 Table
Disables the registered IN point.
53: Out Flag Reset Basic/JVC-1 Table
Disables the registered OUT point.
54: In Flag Recall Basic/JVC-1 Table
Enables the disabled IN point.
55: Out Flag Recall Basic/JVC-1 Table
Enables the disabled OUT point.
58: Go-To In Basic/JVC-1 Table
Executes CueUp to the point registered on the
tape with [50: In Entry] and [E3: In Data Preset].
• The VCR returns [01: Complete] when CueUp is
complete.
• When the specified point is not on the tape, the
VCR returns [05: NotTarget].
• When the IN point is not registered, the VCR
returns [0B: NAK].
59: Go-To Out Basic/JVC-1 Table
Executes CueUp to the point registered on the
tape with [51: Out Entry] and [E4: Out Data Preset].
• The VCR returns [01: Complete] when CueUp is
complete.
• When the specified point is not on the tape, the
VCR returns [05: NotTarget].
• When the IN point is not registered, the VCR
returns [0B: NAK].
5A: Memory Basic/JVC-1 Table
Registers the current time as the Memory point.
5B: Memory Search Basic/JVC-1 Table
Executes CueUp to the point registered on the
tape with [5A: Memory].
• The VCR returns [01: Complete] when CueUp is
complete.
• When the specified point is not on the tape, the
VCR returns [05: NotTarget].
• When the Memory point is not registered, the
VCR returns [0B: NAK].
TxD 3F
RxD 0A
10H 1H 10M 1M
TxD 42 3* 3* 3* 3*
RxD 0A 0A 0A 0A 0A
10S 1S 10F 1F
3* 3* 3* 3*
0A 0A 0A 0A 01
TxD 50
RxD 0A
TxD 4A
RxD 0A
TxD 4B
RxD 0A
TxD 4C
RxD 0A
TxD 4D
RxD 0A
TxD 4E
RxD 0A
TxD 4F
RxD 0A
TxD 51
RxD 0A
TxD 52
RxD 0A
TxD 55
RxD 0A
TxD 53
RxD 0A
TxD 54
RxD 0A
TxD 58
RxD 0A 01
TxD 59
RxD 0A 01
TxD 5A
RxD 0A
TxD 5B
RXD 0A 01
13-2 RS-232C Commands
13 RS-232C protocol
127
72: ROM version JVC-1 Table
Returns the CPU (ROM)’s program version.
• The first byte is fixed at 21.
• The second byte shows the type of software
(D9 = “03”).
• The third byte shows version information.
A0: Standby On Key Basic/JVC-1 Table
Standby On
A1: Standby Off Key Basic/JVC-1 Table
Standby Off
A2: Preroll Key Basic/JVC-1 Table
Rewinds the tape for the preroll time.
• The preroll time is specified by [E6: Preroll Time
Preset].
• When it is not specified, the VCR’s menu setting
is used.
• The VCR returns [01: Complete] after preroll is
complete.
A3: Eject Key Basic/JVC-1 Table
Eject
• When the Eject operation is completed properly,
the VCR returns [03: Cassette Out].
A5: Variable Fwd Key Basic/JVC-1 Table
Variable playback in the forward direction.
Specify the speed with the second byte of TxD.
Refer to the speed/data correspondence table.
(See page 134.)
Auxiliary commands
• Clearing with [56: Clear] and [41: ClearError]
has no effect.
• [40: Enter] has no effect.
A6: Variable Rev Key Basic/JVC-1 Table
Variable playback in the reverse direction.
Specify the speed with the second byte of TxD.
Refer to the speed/data correspondence table.
Auxiliary commands
• Clearing with [56: Clear] and [41: ClearError]
has no effect.
• [40: Enter] has no effect.
TxD 72
RxD 21 03 **
AB:FF Key Basic/JVC-1 Table
Fast-forwarding.
AC: Rew Key Basic/JVC-1 Table
Rewinding.
B2: CueUp With Data Basic/JVC-1 Table
Executes CueUp to the desired point on the tape.
Same as 42: CueUpWithData. (Basic only)
• The VCR returns [01: Complete] after CueUp is
complete.
• When the specified point is not on the tape, the
VCR returns [05: NotTarget].
• Input values of 0 to 9 which follow the second
byte of TxD are expressed with ASCII code.
Auxiliary commands
• [56: Clear] is valid for the second byte or later of
TxD. All commands back to the first byte are
cleared.
•When [02: Error] occurs, [41: ClearError] is
valid. The previous command (one byte) is
cleared.
• [40: Enter] is valid for the second TxD byte or
later. Whatever has not yet been specified is
regarded as [30: Zero].
B2: Play after CueUp With Data JVC-1 Table
Executes CueUp and engages the Play mode.
The VCR returns [01: Complete] after CueUp is
complete.
When the specified point is not on the tape, the
VCR returns [05: NotTarget].
• Input values of 0 to 9 which follow the second
byte of TxD are expressed with ASCII code.
Auxiliary commands
•[56: Clear] is valid for the second TxD byte or later.
All commands back to the first byte are cleared.
• When [02: Error] occurs, [41: ClearError] is valid.
The previous command (one byte) is cleared.
• [40: Enter] is valid for the second TxD byte or
later. Whatever has not yet been specified is
regarded as [30: Zero].
10H 1H 10M 1M
TxD B2 3* 3* 3* 3*
RxD 0A 0A 0A 0A 0A
10S 1S 10F 1F
3* 3* 3* 3*
0A 0A 0A 0A 01
10H 1H 10M 1M
TxD B2 3* 3* 3* 3*
RxD 0A 0A 0A 0A 0A
10S 1S 10F 1F
3* 3* 3* 3*
0A 0A 0A 0A 01
TxD AB
RxD 0A
TxD AC
RxD 0A
13-2 RS-232C Commands
13 RS-232C protocol
TxD A0
RxD 0A
TxD A1
RxD 0A
TxD A2
RxD 0A 01
TxD A5 **
RxD 0A 0A
TxD A3
RxD 0A 03
TxD A6 **
RxD 0A 0A