Filter
Top Products
64
5-2 MENU SWITCH SETTING CONTENT
5 MENU SWITCH SETTING DETAILS
[ ] : Factory setting
Menu SW On-screen Counter On-screen
No. display display display
512 MUTING/ALARM [0] [OFF]
MESSAGE 1 ON
513 EDIT ON 0 OFF
SCREEN [1] [ON]
601 V.BLANK MASK 0 OFF
[1] [ON]
2 ON WITH
0.5H
620 DUBBING LOOP [0] [OFF]
13 TIMES
25 TIMES
3 10 TIMES
Selects whether “MUTING” or “CONDITION
ALARM” messages appear On-Screen.This menu
makes it easier to check the VCR’s operation
status.
The on-screen display is shown on the monitor
connected to the [VIDEO MONITOR OUT]
connector.
OFF:The “MUTING” and “CONDITION ALARM”
are not displayed.
ON :The “MUTING” and “CONDITION ALARM”
are displayed.
For more details, refer to the “MUTING/
CONDITION ALARM” display on page 24.
Selects whether the edit on-screen display is ON or
OFF during editing. On-screen information is output
from the [LINE2 SUPER OUT] connector.
OFF:Does not show the edit on-screen display
during editing.
ON :Show the edit on-screen display during
editing.
<TBC. FRAME MEMORY>
Enables/disables masking of the vertical interval.
OFF :No masking.
ON :Masks the vertical interval.
ON WITH 0.5H:Masks section for 0.5H in addition
to the vertical interval (analog
signals only).
*When this menu is set to “OFF”, only the
recordable sections of the signals output for V.
blanking in the EE mode are output (VITC,
EXTRA LINE, EXTENSION LINE).
When this menu is set to “ON”, VITC and EXTRA
LINE have priority in each menu setting (refer to
page 89).
Selects whether or not the multi-generation test
“Dubbing Loop Function” is used to aid adjusting an
analog component system to unity gain. When this
mode is active, the VCR automatically switches to
its internal color bar generator and continuously
builds the number of generations selected.
OFF : The dubbing loop function is disabled.
3 TIMES : The dubbing loop function repeatedly
builds 3 generations every few seconds.
5 TIMES : The dubbing loop function repeatedly
builds 5 generations every few seconds.
10 TIMES: The dubbing loop function repeatedly
builds 10 generations every few
seconds.
*When set to any setting except OFF (0), this unit
enters the Dubbing Loop mode.
*For more details on the dubbing loop function,
refer to page 122.
Item
Content
Setting
65
6 PREPARATION
6-1 OPERATION MODE LOCK
This unit is provided with an operation mode lock facility. This function prevents accidental changes to switch and
control settings. When this function is ON, currently selected modes and knob or switch positions cannot be
adjusted.
● Use menu switch No. 002 <OPERATION LOCK> to enable this function.
● With this function enabled, operation of all front panel control buttons, adjustment knobs, dials and switches is
disabled and changes to menu switch settings are not possible. When this function is activated, it is not possible
to change menu switch settings. However, the [PHONES LEVEL] control and menu switch No. 002
<OPERATION LOCK> (to release the operation mode lock function) can be used.
Procedure
1. Make all desired settings and operate as usual.
2. Engage the operation lock function.
Press the [MENU] button to call up the menu setting display.
Turn the jog dial and select menu switch No. 002 <OPERATION LOCK>.
If the Direct Access facility is ON, press the [STAND BY] button to call up the
menu item display more quickly.
Select “ON (1)” by turning the jog dial while pressing the [SEARCH] button.
Press the [SET] button.
The operation lock function is ON.
After the SET indication blinks for several seconds, the normal counter and
on-screen displays are restored.
3. To cancel the operation mode lock facility, set menu switch No. 002
<OPERATION LOCK> to “OFF (0)”.
POWER
ON
I
OFF
O
M
H
F
S
REC
MENU
PLAY
PAUSE/ STILL
REW
STOP
FF
EJECT
PHONES
CH1
CH2
CH3
CH4
REC
PLAY
PULL FOR VARIABLE
TRACKING
CH1
CH1
CH2
CH3
CH4/
TRACKING
SET
HOLD
PB
PB/EE
COUNTER
UB
CONDITION
AUDIO
INPUT
VIDEO
INPUT
AUDIO
MONITOR
PULL
RELEASE
RESET
VCON
REMOTE
TOP VIDEO AUDIO
OTHERSON SCREENTIME CODESERVO/SYS
USER
INSERT
STAND BY
PLAYER
SEARCH
VAR
P.PLAY
DA3
DA2
DA1VIDEO
ASSEM
IN
ENTRY
OUT
CANCEL
SHIFT
REVIEW
METER MODE
TRACKING
FINE
PREVIEW
AUTO EDIT
PREROLL
TC
RECORDER
DA4
VIDEO CASSETTE RECORDER
BR-D95U
STILL
X-1
REV
FWD
X1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
SIF
SDI
AES/EBU
AUDIO INPUT / AUDIO MONITOR SELECT
LINE
CPN
L
ANALOG
R
PULL
RELEASE
CTL
P.READ
AUTO
OFF
V.VAR
REMOTE
PB/EE
16:9
TC
UB
DF
SERVO
GENCF
AP
525
OVER
–60
–2
–4
+2
+4
0
–40
–30
–20
–10
0
dB
dB
R
P
OVER
–60
–2
–4
+2
+4
0
–40
–30
–20
–10
0
dB
dB
R P
OVER
–60
–2
–4
+2
+4
0
–40
–30
–20
–10
0
dB
dB
R P
OVER
–60
–2
–4
+2
+4
0
–40
–30
–20
–10
0
dB
dB
R P
625
Variable Motion
COMPONENT DIGITAL
[MENU] button
[HOLD] button
[SET] button
Jog dial
[SEARCH] button