Filter
Top Products
144
ON SCREEN information-2
DATA0 83
Corresponding menu switches
No. Menu switch name Setting Set value
504 INFORMATION TIME 0
SELECT TIME + MODE 1
TIME + SUBTC
3
TIME + SUBTC
4
+ MODE
512 MUTING/ALARM OFF 0
MESSAGE ON 1
513 EDIT ON SCREEN OFF 0
ON 1
TBC information-1
DATA0 84
Corresponding menu switches
No. Menu switch name Setting Set value
620 DUBBING LOOP OFF 0
3TIMES 1
5TIMES 2
10TIMES 3
TBC information-3
DATA0 86
Corresponding menu switches
No. Menu switch name Setting Set value
601 V BLANK MASK OFF 0
ON 1
ON WITH 0.5H 2
TIME CODE information-4
DATA0 77
Corresponding menu switches
No. Menu switch name Setting Set value
400p
VITC LINE-1 SEL 70
(625) : :
22 15
401p
VITC LINE-2 SEL 7 0
(625) : :
22 15
TIME CODE information-5
DATA0 78
Corresponding menu switches
No. Menu switch name Setting Set value
421 TCG CF FLAG OFF 0
ON 1
AUTO 2
ON SCREEN information-1
DATA0 82
Corresponding menu switches
No. Menu switch name Setting Set value
501 CHARA H POSITION 00
::
66
502 CHARA V POSITION 00
::
11 11
505 REMAIN ENABLE DISABLE 0
ENABLE 1
76543210
D1 504 504 513 512 504
D2
13-5 Menu switch setting information
13 RS-232C protocol
76543210
D1 401p 401p 401p 401p 400p 400p 400p 400p
D2
76543210
D1 421 421
D2
76543210
D1 502 502 502 502 501 501 501 501
D2 505
76543210
D1
D2 620 620
76543210
D1
D2 601 601
145
WARNING 01 1
LAMP FAILURE
Main code
Sub code
M
H
F
S
CONDITION
AUTO
OFF
Warning On-screen display Warning code information Behavior and actions to be taken
code
0A FAN FAILURE The power turns OFF after
about 9 minutes.
01 1 LAMP FAILURE Tape sensor LED broken.
(AUTO OFF)
02 1 CONDENSATION ON Condensation on drums.
DRUM
06 1 INVALID ERROR S-VHS/VHS cassette in use.
08 1 SUP TENSION Tape tension abnormal.
(AUTO OFF)
FAILURE
32 1~ FAILURE LOADING Tape loading not possible.
32 2
33 1~ FAILURE UNLOADING
Tape unloading not possible.
33 2
(AUTO OFF)
Warning messages on
the on-screen display
Warning messages on
the counter display
As this unit uses a microcomputer, it may not
function correctly due to noise from outside or
interference noise. In this case, unplug the power
cord and plug it again. Then, check the operation.
14 TROUBLESHOOTING
14-1 WARNINGS WITH INDICATORS
This machine features self-diagnostic circuitry which allows it to detect and report any malfunctions that may
occur. When a malfunction is detected, the cause will be shown on the monitor display and on the VCR’s counter
display. The warning code system consists of a main code (the code number) and a sub code (verbal descrip-
tion), e.g. 02 1 CONDENSATION ON DRUM. The front panel [AUTO OFF] indicator will normally be illuminated.
* When the [AUTO OFF] indicator is illuminated, the unit is no longer operable. The [AUTO OFF] indicator can be
canceled by turning the power off and on again. If the indicator remains lit even after turning the power off and
on, malfunctions are possible. Consult your local JVC dealer.
Turn the [POWER] switch OFF. Wait for at
least 5 minutes, then turn the power ON
again.
If the warning indication is displayed again,
consult your local JVC dealer.
Behavior:Stops, with no operation possible.
Action: Turn the power off and then on.
Behavior:Cassette ejected and drum begins
to rotate. When condensation is
eliminated, the indicator goes out
and cassette can be loaded.
Action: Leave the power ON and wait until
the waraning message goes out.
Behavior:Stops, with no operation possible.
Action: Turn the power off and then on.
Behavior:Cassette ejected.
Action: Load the cassette again.
Behavior:Stops, with no operation possible.
Action: Turn the power off and then on.
Behavior:Cassette ejected.
Action: Use Digital-S cassette tape.
Refer to “1.8 WARNING DETECTION CIRCUIT” on page 1.12 of the service manual.
←