Filter
Top Products
100 English
RECORD SET2
INTRODUCTION SETTINGS NETWORK
CONTROL
NETWORK
OPERATION
NETWORK
SETTINGS
OTHEROPERATION
10 Turn the shuttle dial clockwise.
“ONLY” flashes.
11 Turn the jog dial to select the “ALARM
INTERLEAVE” setting and then turn the
shuttle dial clockwise.
The cursor moves to “REC RATE/DURATION”.
[Settings] ( indicates default setting)
* Example of recording pattern for SW and ONLY
12 Turn the shuttle dial clockwise.
If “ALARM INTERLEAVE (step 11)” is set to other than the
program mode, you see “A12.5FPS” flash for “REC RATE”,
indicating that setting is acceptable.
13 Turn the jog dial to select the “REC
RATE” setting and then turn the shuttle
dial clockwise.
The cursor moves to “DURATION”.
[Settings] ( indicates default setting)
z If “ALARM INTERLEAVE (step 11)” is set to program
mode, “****” is displayed and you cannot select the
recording rate.
Setting Description
ONLY
Video is recorded only from cameras with an
alarm occurring.
SW
Recording is switched between video from a
camera for which an alarm has occurred and
video from all connected cameras.
ALL
When any one of the cameras receives an
alarm, all connected cameras start recording
in order.
ONLY (P-1)
ONLY (P-2)
ONLY (P-3)
ONLY (P-4)
<“ONLY” program mode>
When a connected camera registered in the
program recording setting receives an alarm,
video recording starts at a recording rate
specified in the program.
z Specify the program you want to apply from
“P-1” to “P-4”.
z Audio recording is not available.
ALL (P-1)
ALL (P-2)
ALL (P-3)
ALL (P-4)
<“ALL” program mode>
When any one of the connected cameras
registered in the program recording setting
receives an alarm, video recording starts for all
the connected cameras at a recording rate
which was independently specified for each
connected camera in the program.
z Specify a program you want to apply from
“P-1 to P-4”.
z Audio recording is available only when any
one of the cameras has a recording rate of 1
FPS or more.
<ALARM REC MODE SET>
ALARM RECORDING : ENABLED
PICTURE QUALITY : ENHANCED
PICTURE QUALITY SET ->
AUDIO RECORDING : ON
ALARM INTERLEAVE : ONLY
REC RATE:A12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING : OFF
REC RATE: ***** FPS, DURATION: *****
ALARM TRIGGER : ALARM
MOTION SENSOR ->
<ALARM REC MODE SET>
ALARM RECORDING : ENABLED
PICTURE QUALITY : ENHANCED
PICTURE QUALITY SET ->
AUDIO RECORDING : ON
ALARM INTERLEAVE : ONLY
REC RATE:A12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING : OFF
REC RATE: ***** FPS, DURATION: *****
ALARM TRIGGER : ALARM
MOTION SENSOR ->
Setting Description
50, 25, 16.67, 12.5,
8.333, 6.25, 5, 4.167,
3.571, 3.125, 2.778, 2.5,
2.273, 1.923, 1.667,
1.471, 1.316, 1.19, 1.087,
1, 0.5, 0.333, 0.25, 0.2,
0.1, 0.05, 0.033
Recording is performed at the
selected recording rate (unit: FPS).
02 02 02 02 020201 03 04
02 02 02 02 0201 03 04 040405 06 07 08
Alternate recording of multiple alarm recordings
Recording until alarm is cancelled
Alarm Alarm
Alarm Alarm is cancelled
SW
ONLY
<ALARM REC MODE SET>
ALARM RECORDING : ENABLED
PICTURE QUALITY : ENHANCED
PICTURE QUALITY SET ->
AUDIO RECORDING : ON
ALARM INTERLEAVE : ONLY
REC RATE:A12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING : OFF
REC RATE: ***** FPS, DURATION: *****
ALARM TRIGGER : ALARM
MOTION SENSOR ->
<ALARM REC MODE SET>
ALARM RECORDING : ENABLED
PICTURE QUALITY : ENHANCED
PICTURE QUALITY SET ->
AUDIO RECORDING : ON
ALARM INTERLEAVE : ONLY
REC RATE:A12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING : OFF
REC RATE: ***** FPS, DURATION: *****
ALARM TRIGGER : ALARM
MOTION SENSOR ->