Filter
Top Products
3745 Panel Codes
Table 1-5 (Page 30 of 33). Panel Codes. An
following a panel code denotes that the code should 'Blink'.
Panel
Code
Definition
Action: Go to “3745 FRU Group
Table” on page 1-49
or to MAP number
F36 to F47 Unused
Go to “MAP 3220: Undefined Panel
Message” on page 2-5
F48
Errors detected during the IPL sequence; CCU and
CACHE checkout failed SCTL checkout failed
A reference code will have been
produced on the 3745 console. Refer
to “Using Reference Codes” on
page 1-14.
F49 Unused
Go to “MAP 3220: Undefined Panel
Message” on page 2-5
F4A
Errors detected during the IPL sequence; SCTL initial-
ization failed
A reference code will have been
produced on the 3745 console. Refer
to “Using Reference Codes” on
page 1-14.
F4B
Errors detected during the IPL sequence; switch
checkout failed
F4C
Errors detected during the IPL sequence; permanent
level 1 in CCU, no need to load CLDP
F4D
Errors detected during the IPL sequence; channel moni-
toring failure in normal monitor mode, during FB or SB
F4E
Errors detected during the IPL sequence; reset
adapters can not be performed during FB or SB
F4F
Errors detected during the IPL sequence; problem
detected by the CDF
F50
Errors detected during the IPL sequence; CP not set
ONLINE by the fallback or switchback
F51
Errors detected during the IPL sequence; bus switching
operation unsuccessful
F52
Errors detected during the IPL sequence; problem
detected with the MCAD interface
A reference code will have been
produced on the 3745 console. Refer
to “Using Reference Codes” on
page 1-14.
F53
Error detected during the IPL sequence; fallback func-
tion not supported
F54
Errors detected during the IPL sequence; no buffer
available for NCP during fallback
F55
Errors detected during the IPL sequence; NCP / MOSS
fallback interface error
F56
Errors detected during the IPL sequence; interface
problem between fallback-switchback and channel mon-
itoring
F57
Errors detected during the IPL sequence; CCU power
has dropped during the IPL
A reference code will have been
produced on the 3745 console. Refer
to “Using Reference Codes” on
page 1-14.
F58
Errors detected during the IPL sequence; error during
SBK protocol
F59
Error detected during MOSS IML diagnostics; IPL can
not be performed on the selected CCU
F5A
Errors detected during the IPL sequence; CA configura-
tion from CDF does not match the actual configuration
F60
Error detected during MOSS IML Diagnostics; IPL can
not be performed on CCU
F61 IPL cancelled after IPL abort
F62
Error detected during MOSS IML Diagnostics; IPL can-
celled after a stop in phase 1 diagnostic
F63 to FD5 Unused
Go to “MAP 3220: Undefined Panel
Message” on page 2-5
FD6
Status/progression step which occurs during the IPL
sequence; the control program loading is started from
the Disk
If this code is displayed for more than
2 minutes, when the load/dump is via
the disk, then refer to “How to Run
MOSS Diagnostics” on page 3-4 to
aid problem isolation and refer to
IBM
3745 Service Functions
, "Hard Disk
Trouble Analysis".
FD7
Status/progression step; dump control program on
MOSS disk in progress
FD8
Status / Progression step; save control program on
MOSS disk in progress
FD9 to FE0 Unused
Go to “MAP 3220: Undefined Panel
Message” on page 2-5
1-44 3745 Models 130 to 17A: MIP