Mitsubishi Electronics FX5 Universal Remote User Manual


 
276
APPENDIX
Appendix 3 Error Code
1FE5H Module
configuration
error
The I/O numbers of the reserved module
specified in the I/O assignment setting of
the parameters overlap those of other
modules.
Make sure that the parameters are
consistent with the connections.
System
configuration
information
At power-on,
at RESET
1FE6H Module
configuration
error
The I/O method of the input/output
module is different.
Make sure that the parameters are
consistent with the connections.
System
configuration
information
At power-on,
at RESET
1FE7H Module
configuration
error
The type of the CPU module is different. Make sure that the parameters are
consistent with the connections.
System
configuration
information
At power-on,
at RESET
2003H Module
configuration
error
The model of the module connected is
different from that of the module set in
the parameters.
Make sure the model of the module to be set
is consistent with the parameters of the
module connected.
System
configuration
information
At power-on,
at RESET
2008H Module
configuration
error
The total number of I/O points (excluding
remote I/O) exceeded 256.
Do not use more than 256 I/O points in
programs.
System
configuration
information
At power-on,
at RESET
2042H CPU module
configuration
error
The number of input, output, input/
output, and intelligent function modules
connected is equal to or greater than 17.
The number of communication adapters
connected is equal to or greater than 3.
The number of analog adapters
connected is equal to or greater than 5.
The number of extension power supply
modules connected is equal to or greater
than 3.
The number of expansion boards
connected is equal to or greater than 2.
Use up to 16 input, output, input/output, and
intelligent function modules.
Use up to 2 communication adapters.
Use up to 4 analog adapters.
Use up to 2 extension power supply
modules.
Use up to 1 expansion board.
System
configuration
information
At power-on,
at RESET
20E0H Invalid module
detection
An unsupported module was detected. Verify that the version of the CPU module is
compatible with the module where the error
was detected.
If the version of the CPU module is correct,
there may be a malfunction in the connected
module. Replace the connected module.
System
configuration
information
At power-on,
at RESET
2120H Memory card
error
An SD memory card error was detected.
The SD memory card may have been
removed without the SD memory card
disabled.
Check the connection of the SD memory
card. If the problem persists, there may be a
malfunction in the SD memory card or CPU
module.
Drive/file
information
Always
2121H Memory card
er
ror
An SD memory card error was detected.
The SD memory card may not be
correctly formatted.
Format the SD memory card. If the problem
persists, there may be a malfunction in the
SD memory card or CPU module.
Drive/file
information
Always
2180H Invalid file • An error was found in the data of the file. Recreate the file. Drive/file
information
At power-on,
at RESET, at
STOP
RUN state
21A0H File specification
error
The file specified in the parameters does
not exist.
Rewrite the project. Drive/file
information
Parameter
information
At power-on,
at RESET, at
STOP
RUN state
2220H Parameter error • The contents of the parameters are
corrupted.
Rewrite the project. Parameter
information
At power-on,
at RESET
2221H Parameter error • The parameter set value is out of range. Modify the parameter set value and rewrite
the project.
Parameter
information
At power-on,
at RESET
2222H Parameter error • The parameter set value is out of range. Modify the parameter set value and rewrite
the project.
Parameter
information
At power-on,
at RESET
2241H Parameter error
(module)
The module parameter settings and the
target module are different.
Modify the module parameter set value and
rewrite the project.
Parameter
information
At power-on,
at RESET
2300H Security key
authentication
error
The security key locking the program
does not match the security key written
in the CPU module.
Write the correct security key to the CPU
module.
Drive/file
information
At power-on,
at RESET, at
STOP
RUN state
Error
code
Error name Error details and cause Action Detailed
information
Diagnostic
timing